HONDA marine BF25D Скачать руководство пользователя страница 96

Страница: 96 / 141

STORAGE

If the outboard motor will be

removed from the boat for storage,

we recommend storing it vertically by

mounting it on a commercially

available stand.

If it is necessary to store the outboard

motor horizontally, drain the

carburetors (p. 92), and drain the

engine oil (p. 73), before removing

the outboard motor from the boat.

Position the outboard motor with its

carburetor side down, and cushion it

with protective packing material.

Any other horizontal storage position

may cause damage to the outboard

motor or oil leakage.

Cover the outboard motor to keep out

dust. Do not use a plastic sheet as a

dust cover. A nonporous cover will

trap moisture, promoting rust and

corrosion.

REMOVAL FROM STORAGE

Check your outboard motor as

described in the

BEFORE

OPERATION

chapter of this manual.

If the cylinders were coated with oil

during storage preparation, the engine

may smoke briefly at startup. This is

normal.

CASE PROTECTOR

31ZW26430.book Page 94 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды