HONDA marine BF25D Скачать руководство пользователя страница 53

Страница: 53 / 141

OPERATION

• Using the electric starter for more

than 5 seconds at a time will

overheat the starter motor and can

damage it.

• Turning the ignition switch key to

the START position while the

engine is running can damage the

starter motor and flywheel.

5. Before getting underway, allow the

engine to warm-up sufficiently to

ensure good performance.

Above 41°F (5°C), warm-up the

engine for at least 3 minutes.

Below 41°F (5°C), warm up the

engine for at least 10 minutes at

approx. 2,000 rpm.

• If the engine is not properly

warmed up before raising the

engine speed, the buzzer and

overheat indicator may activate

and the engine speed will be

automatically reduced.

• The cooling system may freeze in

areas where the temperature

reaches 32°F (0°C) or below.

Cruising at high speed without

warming the engine up may cause

engine damage.

During the warm-up period, check

the oil pressure indicator (p. 30),

overheat indicator (p. 31), and

cooling system indicator (p. 31).

If the indicators show any

abnormal condition, immediately

stop the engine and determine the

cause of the problem. Refer to

TAKING CARE OF

UNEXPECTED PROBLEMS

p. 104.

6. If the fast idle lever was used to

start the engine, gradually lower

the lever as the engine warms up.

When the fast idle lever is fully

lowered, the control lever can be

moved away from the N (neutral)

position.

FAST IDLE LEVER

31ZW26430.book Page 51 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды