4
**note:
some devices react to signals slower, so make sure you wait for enough time between pressing
the POWER button again and again. All buttons function properly in code search mode, so they you can
test them before moving on to the next code. Pressing the SET button changes the search direction.
You can exit the quick search mode by pressing any device selection button (e.g. TV) or by not pressing
any button for 30 seconds.
Automatic quick search
This function automatically runs through all codes. You may as well put the remote control on your
coffee table and wait for your device to react.
1. Turn on manually the device you want to operate.
2. Press the appropriate device selection button (e.g. TV)
3. Press and hold the SET button and, while doing so, press the POWER button. The LED will go on
after 3 seconds
4. Direct the remote control toward the device and release all buttons. The remote control will
start running through the codes automatically.
5. If the device reacts to any of the codes, you can stop the automatic process by pressing any of
the buttons. After having run through all the codes, the LED will go off and the remote control
will switch off. This may take a few minutes.
Reading a selected code
If you fi nd the proper code with the quick search function, it is advisable to note it down to make
its reselection easier. You can check the selected value using the buttons on the remote control
and reading its display. The number of the fl ashes the LED makes is equal to the fi rst, second, third
and fourth digits of the four-digit number respectively.
Press the button of the device whose code you wish to check. (TV, VCR, SAT, CBL, AUX). Press and
hold the SET button and, while doing so, press a number button (1-2-3-4) to fi nd out the values of
the various digits. Then release both buttons and count the fl ashes.
For example, if the selected code is 0261:
1. SET + ”1”: 0 fl ash
2. SET + “2”: 2 fl ashes
3. SET + “3”: 6 fl ashes
4. SET + “4”: 1 fl ash
note:
no fl ash means zero
Battery replacement
If the or the effi cient range reduces, you should change the batteries. Open the cover of battery-
holder. After that set in 2 pcs AAA, 1,5 Volt batteries according to polarity.
Codes selected earlier are retained in the memory while batteries are being replaced. Pressing
any of the buttons while replacing the batteries may result in data loss!
Warning
• Do not expose the remote control to direct heat, sunlight, dust, steam or shock.
• Remove dust regularly using a soft cloth.
• Make sure that no liquid substance is spilt on the keypad.
• Take care of the correct polarity during setting of batteries.
• If you do not use the device for long time, take out the batteries.
• Never try to disassemble the device, take it to professional!
Technical data
system: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pre-programmed, infra red
range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 m
power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x AAA (1,5 V) (not included)
size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 x 23 x 196 mm
