8
9
INSTALLATION INSTRUCTIONS
UNPACKING AUNPACKING AND REMOVING SHIPPING MATERIAL
Before beginning assembly of the product, make sure all parts are present. Compare parts in the package with hardware
and accessories list below. If any part is missing or damaged, do not attempt to assemble the product. Contact customer
service for replacement.
Parts Description
A
B
FF
C
D
E
G
OO
NN
H
F
I
J
K
L
N
O
M
Tools Needed (not included)
Phillips screwdriver with medium blade. Leak Detection
Solution.
Estimated assembly time: 60 minutes
ASSEMBLY INSTRUCTIONS
1. Bucket assembly:
1-1. Attach wheel kit (J) to
base (I). Line up holes in wheel
bracket with corresponding
holes in base, insert two bolts
M8 x 16 (BB) through holes,
and finger tighten two M8
flange nuts (AA). Reverse the
base, fix the ground fixer (K) to
the base with two bolts M6X10
(DD) and two washers Ø6 (EE),
Secure the ground fixer with
two nuts M6 (PP). Fix another two ground fixer with bolts
and nuts, and reverse the base. (Screws for anchoring
the base to the ground are not
inculded.)
1-2. Insert four M8X45 screw
(QQ) through holes , and finger
tighten four M8 flange nut
(AA)
.
1-3. To improve the stability,
the bucket (L) must be filled
with sand. Remove the lid
from center of bucket (L).
Slowly pour the sand into the
bucket (L). Shake the bucket
(L) to disperse the sand
evenly. Close the lid tightly.
2. Attach cylinder
housing (G) to base (I).
Attach cylinder housing
loosely to base with
four M5 X 8 screws
(CC).
3. Attach post (H) to
cylinder housing top.
Open the door, put
post through the hole
on the top of cylinder
housing.
4. Attach post to cylinder
housing using the
reinforced ring (NN), four
M6 X 10 bolts (DD) and
small flat washers Ø6
(EE). Fasten them and
cover with the deck ring
(OO).
1-2
I
AA
L
1-1
I
AA
PP
EE
K
DD
BB
1-3
san
d
L
2
G
CC
3
H
4
NN
oo
Accessories
AA
II
DD
EE
HH
K
CC
KK
LL
MM
NN
FF
BB
GG
Reflector
spacer
Qty.
3
Washer
Φ
8
Qty.
9
Washer
Φ
6
Qty.
9
Screw
M6 X 10
Qty.
9
Cap nut
Qty.
9
Screw
M5 X 8
Qty.
8
Bolt M6 X 10
Qty.
10
Small flat
washer
Φ
6
Qty.
10
Reinforced
ring
Qty.
1
Wrench
Qty.
1
JJ
Wing nut
Qty.
3
Stainless
steel bolt
Qty.
4
Bolt
M8 x 16
Qty.
2
Qty.
4
M8
Flange
nut
Qty.
6
(not actual size)
(not actual size)
OO
Deck ring
Qty.
1
PP
M6 Nut
Qty.
6
(not actual size)
Qty
. 3
Ground Fixer
Screw
M8x45
INSTALLATION INSTRUCTIONS
A
Reflector Panel X 3
B
Reflector Plate
FF
Reflector Stud X 3
C
Head Assembly (Burner)
D
Tabletop
E
Table connector
F
Regulator
OO
Deck Ring
NN
Reinforced Ring
G
Cylinder Housing
H
Post
I
Base
J
Wheel Kit
K
Ground Fixer X 3
L
Bucket
M
Orifice
N
Thermocouple
O
Pilot tube
