background image

9

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

Assembly - Hanging the Fan (continued)

3

NOTE:

 The frequencies on your receiver and hand unit have 

been preset at the factory. Before installing the receiver, 

make sure the dip switches on the receiver and hand unit are 

set to the same frequency. The dip switches on the hand unit 

are located inside the battery compartment.

NOTE: 

The switch marked “O/D” controls the dimming 

function of the lights. If using non-dimmable bulbs, use a 

ballpoint pen or small screwdriver to set the switch to “O” to 

disable the dimming function. If using dimmable bulbs, set 

the switch to “D” to enable the dimming function.

Setting the code on the remote 
control and receiver

 

Remove the remote control (K) battery cover by pressing 
firmly on the arrow and sliding the cover off.

 

Slide the dip switches (ZZ) to your choice of either up or 
down. The factory setting is up.

 

Slide the dip switches (ZZ) on the receiver (J) to the same 
position as set on the remote control (K).

 

Install the 23A 12V batteries (included).

 

Replace the battery cover on the remote control (K).

 

Insert the silicone rubber stopper (OO) into the hole on the 
receiver (J) to cover the dip switches.

NOTE:

 The battery will weaken with age and should be 

replaced before leaking takes place as this will damage the 

hand unit. Dispose of used battery properly and keep the 

battery out of the reach of children.

4

Installing the receiver

 

Position the house supply wires (AAA) to one side of the 
slide-on mounting bracket (A); position the fan wires (BBB) 
to the opposite side. 

 

Insert the narrow end of the receiver (as shown, flat side 
towards the ceiling) into the slide-on mounting bracket until 
it rests on top of the ball/downrod assembly.

WARNING:

 To reduce the risk of fire or electric shock, 

remember to disconnect power. The electrical wiring must 

meet all local and national electrical code requirements. 

The electrical source and fan must be 110/120 volt, 60Hz. 

Do not use this product in conjunction with any variable wall 

control. Incorrect wire connection can damage this receiver.

CAUTION:

  If other fan wires are a different color, have this 

unit installed by a licensed electrician.

CAUTION:

 Do not install the receiver in a damp location or 

immerse in water (For indoor use only). Do not pull on or cut 
the receiver leads shorter. Do not drop or bump the unit.

K

J

ZZ

12

34

ON

DIP

1 2

3 4

ON

OO

D

O

B

C

AAA

BBB

A

J

Содержание 59242
















Отзывы: