Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (E) into the tree stand and tighten the screw.
(See Fig. 1)
Step 2. Insert lower middle section (D) into the tree bottom (E). (See Fig. 2)
Step 3. Insert the middle section (C) into the lower middle section (D). (See
Fig. 3)
Step 4 Insert upper middle section (B) into the middle section (C). (See
Fig. 4)
Step 5. Insert tree top (A) into the upper middle section (B). (See Fig. 5)
Step 6. Insert the provided power cord into the connector on the tree
bottom (E) in right direction properly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (E) according to the
magnified drawing on fig. 6.).
Step 7. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 7)
Step 8. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the main
stem. Repeat pattern for each branch. (See Fig. 8)
Step 9. Plug the power cord into a proper outlet. This tree comes with a
control box and a remote control for easy illumination and
changing functions. This tree is Color Changing, the 8 lighting
options available are:
1.
Steady Warm White
2.
Flashing Warm White
3.
Fade In and Fade Out Warm White
4.
Steady Multicolor
5.
Flashing Multicolor
6.
Fade In and Fade Out Multicolor
7.
Sequential Multicolor & Warm White
8.
Color Changing
These functions can be changed by using control box or remote
control.
Please see Instructions of control box and remote control as
below.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the well-connected power
cord into a wall outlet.
Instruction of control box and remote
control
Instruction of control box
1.
Press the ON/OFF button on control box to turn on and off the tree
lights.
2.
Press the MODE button on control box to select below functions:
1.
Steady Warm White
2.
Flashing Warm White
3.
Fade In and Fade Out Warm White
4.
Steady Multicolor
5.
Flashing Multicolor
6.
Fade In and Fade Out Multicolor
7.
Sequential Multicolor & Warm White
8.
Color Changing
3. In the state of function 2, 3, 5, 6, 7 or 8:
press the SPEED + button, the speed of the corresponding function is
faster.
press the SPEED - button, the speed of the corresponding function is
slower.
There is memory mode on functions whether the tree is re-started.
It has Output Short-circuit Protection
When the load is short-circuited, the output can be automatically
closed. After eliminating the short circuit and restarting the power on,
it can return to normal.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1.
Press Fn button, the function below cycle. Press the number key,
select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function 2: Flashing Warm White
Function 3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function 5: Flashing Multicolor
Function 6: Fade In and Fade Out Multicolor
Function 7: Sequential Multicolor & Warm White
Function 8: Color Changing
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1.
Replace with a new button cell “CR2025” (3 volt)
into the compartment.
CAUTION:
DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
Vents
