If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1.
Pull the reflector out.
2.
Remove the base of burned out
lamp by straightening lamp leads
and gently pulling lamp out.
3.
Thread leads of new lamp through hole in old base with one lead in
each hole (always match the long lead of new lamp to the hook of
lamp base.)
4.
After bulb is fully inserted, bend each lead up so that the leads will
touch the contacts inside the bulb holder.
5.
Insert the reflector into the base.
CAUTION! –
ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE AND BULB
REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet.
Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Use and Care Instructions
a)
Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged, or frayed wire insulation or cords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
b)
When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to avoid
any undue strain or stress on the product conductors, connections,
and wires.
c)
When not in use, store neatly in a cool, dry location protected from
sunlight.
CAUTION
a)
To reduce the risk of electric shock, use only with the power-supply
cord provided or with a cord set intended for indoor use.
b)
Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c)
Do not abuse cord – Do not carry product by the cord or yank or pull
it to disconnect from the outlet.
d)
Disconnect the product from the outlet when not in use.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well. Make sure the plug of power supply
extension cord from the bottom section (C) is securely
inserted into a working electrical outlet.
Check for blown fuses at the power cord plug. Replace
as needed with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-855-HDHoliday (1-855-434-6543) for
instructions.
Loose branches
If a branch of the tree falls off, follow the steps below to reinstall it with a
spare rivet (H).
1)
Place the branch into the slot of the bracket.
2)
Insert a spare rivet through
the hole and use diagonal
pliers (not included) to crimp
the rivet. (See Fig. A)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Warning
: Please note that changes or modifications
of this product is not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician
for help.
WARRANTY
3-year Limited Warranty
This product carries a three (3) year warranty against defects
in workmanship and materials. This product is not
guaranteed against wear or breakage due to misuse and/or
abuse.
Date Code: 04012022_2003186
Importer: The Home Depot
Address: 2455 PACES FERRY ROAD ATLANTA, GA 30339
Tel: 1-855-HDHoliday (1-855-434-6543)
Model No. TMP7.5-6(0.64)
