Turning on the tree
Step 1. Plug the well-connected power cord from the tree section (C)
into a proper outlet.
Replace the fuse.
1.
Fuse replacement of power supply cord from bottom section (C)
(replaceable 3 amp, 125 volt fuse is located in spare parts bag):
a)
Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
b)
Open fuse cover. Slide open fuse access
cover on top of attachment plug towards
blades.
c)
Remove fuse carefully.
d)
Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse
(provided with product).
e)
Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f)
Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
2.
Fuse replacement of power supply extension cord with foot pedal
switch (replaceable 5 amp, 125 volt fuse is located in the plug):
This plug will fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not use with an extension cord
unless plug can be fully inserted. Do not alter or replace the plug.
a)
Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
b)
Open fuse cover. Slide open fuse access
cover on top of attachment plug towards
blades.
c)
Remove fuse carefully.
d)
Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse
(provided with product).
e)
Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f)
Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
a)
Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
b)
Unlock the burned out LED bulb by lifting the hook and pulling both
the bulb and plastic base straight out of the bulb holder. Do not twist
bulbs.
c)
Replace burned out bulb with 3.0 volt, 20 mA LED type bulb ONLY.
(Replacement bulbs included)
d)
Lock the LED bulb.
CAUTION
1.
To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0 Volt, 20 mA LED lamps only.
2.
Risk of fire. This product does not contain lamp shunts, which allow the
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1.
Pull the reflector out.
2.
Remove the base of burned out lamp by straightening lamp leads
and gently pulling lamp out.
3.
Thread leads of new lamp through hole
in old base with one lead in each hole
(always match the long lead of new lamp
to the hook of lamp base.)
4.
After bulb is fully inserted, bend each lead up so that the leads will
touch the contacts inside the bulb holder.
5.
Insert the reflector into the base.
CAUTION! –
ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE AND BULB
REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet.
Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Use and Care Instructions
a)
Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged, or frayed wire insulation or cords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
b)
When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to avoid
any undue strain or stress on the product conductors, connections,
and wires.
c)
When not in use, store neatly in a cool, dry location protected from
sunlight.
Operation
Maintenance
