5.
Flashing Multicolor
6.
Slow Fade Multicolor
7.
Sequential Multicolor & Warm White
8.
Slow Fade Multicolor & Warm White
Operation
Turning on the tree
NOTE: If some bulbs do not light or flicker, search for any loose, broken
bulbs and /or missing bulbs. Replace bulbs promptly with the
replacement bulbs provided in order to maintain the performance and life
expectancy of your tree.
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Maintenance
Fuse Replacement
A) Extension cord fuse replacement (1 replaceable 3 A, 125 V fuse is
located in the plug):
Note: This plug will fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug.
1. Grasp plug and remove from its power source.
2. Locate blown fuse by sliding access cover on
top of plug towards prongs.
3. Remove blown fuse by turning the plug over.
Fuses should fall into your hand (gentle tapping
may be required).
4. Locate spare replacement fuse included in plug.
5. Insert spare replacement fuse. Close fuse cover by sliding fuse access
cover towards the cord.
CAUTION
:
To reduce risk of fire – replace fuse in extension
cord with only 3 A, 125 V fuse. Do not replace attachment plug. Discard
product if the attachment plug is damaged.
Replacing the bulbs
1. Grasp plug and remove from its power source.
2. Unlock the lamp lock on the socket of the bulb.
3. Pull bulb AND plastic base straight out of socket. Do not twist bulbs
while you are removing them.
4. Replace burnt out bulb with 3.0 V, 0.06 W LED bulb ONLY. (Additional
bulbs are included for your convenience.)
5. Relock the lamp lock on the socket of the bulb.
If the new lamp base does not fit in lampholder, follow these steps:
Pull reflector out.
Remove the base of the burned-out
bulb by straightening the bulb leads,
and gently pull bulb out.
Thread leads of new bulb through
holes in old base with one lead in each hole.
After bulb is fully inserted into base, bend each lead up so that the
leads will touch the contacts inside the bulb holder.
Insert the reflector into the base.
CAUTION! –
ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ATTEMPTING
FUSE AND BULB REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the plug cord from the wall outlet. And remove your power
supply cord with an on/off foot pedal switch from bottom section
(C) and save it.
Step 3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it
shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Warning: Please note that changes or modifications not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
Troubleshooting
Problem
Solution
The tree does
not light
Ensure that all tree sections are connected well into
each other and that the tree is plugged into the wall
outlet.
Check for blown fuses at the power cord plug.
Replace as needed with the replacement fuses
provided.
Check for loose, broken, or missing bulbs and
replace as needed with the replacement bulbs
provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
