manualshive.com logo in svg

HOLZTECH S1.6, Инструкция по эксплуатации, Страница: 12 / 46

Поделиться
Скачать
HOLZTECH S1.6 Скачать руководство пользователя страница 12

Holztech S3.0 S2.5 S1.6

WWW.HOLZTECH.COM

7.  Preparing the machine for first use

7.1 Cleaning

All shining parts, which were protected against rust for transport, must be cleaned with petrol
or another degreasing products.

ATTENTION: Don’t ever use nitrothinning products or other solving products!

Don’t ever use water!

7.2 Building up

The machine must be levelled with all 4 installation feet, on a flat surface with a sufficient
bearing power.

The levelling operation of the machine can be done by turning the installation screws on the
feet of the machine.

Pay attention to have enough space around the machine.
This makes working more easy and lowers the danger level.

7.3 Preparation before working

7.3.1 

Mounting the additional table F (picture 5)

a)  Loosen the transport security A from the telescopic support B.
b)  Move the groove core D in the T-groove at the roller table.
c)  Short screw the screw C with the add-ins to the thread D.
d)  Place the additional table F on the bolts G and the screws C.
e)  Test, if the onlay surfaces of both tables are parallel to each other and or on equal

heights.
When needes, you can change the installation with installation screws H und L.

Содержание S1.6















































Отзывы:

Нет отзывов