manualshive.com logo in svg

Holtek BS66F340, Руководство пользователя

Микросхема Holtek BS66F340 -совершенный контроллер, обеспечивающий стабильную и эффективную работу устройства. Для дополнительной поддержки и понимания работы устройства, вы можете бесплатно скачать руководство пользователя на manualshive.com. Необходимая документация для успешной эксплуатации устройства.

Поделиться
Скачать
background image

Rev. 1.60

136

August 20, 2019

Rev. 1.60

137

August 20, 2019

BS66F340/BS66F350/BS66F360/BS66F370

Touch A/D Flash MCU with LED Driver

BS66F340/BS66F350/BS66F360/BS66F370

Touch A/D Flash MCU with LED Driver

a compare match occurs. After the PTM output pin changes state, it can be reset to its 

initial level by changing the level of the PTON bit from low to high.
In the PWM Mode, the PTIO1 and PTIO0 bits determine how the TM output pin 

changes state when a certain compare match condition occurs. The PTM output function 

is modified by changing these two bits. It is necessary to only change the values of the 

PTIO1 and PTIO0 bits only after the PTM has been switched off. Unpredictable PWM 

outputs will occur if the PTIO1 and PTIO0 bits are changed when the PTM is running.

Bit 3

 PTOC

: PTM PTP Output control

Compare Match Output Mode

0: Initial low

1: Initial high

PWM Output Mode/Single Pulse Output Mode

0: Active low

1: Active high

This is the output control bit for the PTM output pin. Its operation depends upon 

whether PTM is being used in the Compare Match Output Mode or in the PWM 

Mode/Single Pulse Output Mode. It has no effect if the PTM is in the Timer/Counter 

Mode. In the Compare Match Output Mode it determines the logic level of the PTM 

output pin before a compare match occurs. In the PWM Mode/Single Pulse Output 

Mode it determines if the PWM signal is active high or active low.

Bit 2

 PTPOL

: PTM PTP Output polarity control

0: Non-inverted

1: Inverted

This bit controls the polarity of the PTP output pin. When the bit is set high the PTM 

output pin will be inverted and not inverted when the bit is zero. It has no effect if the 

PTM is in the Timer/Counter Mode.

Bit 1

 PTCAPTS

: PTM Capture Triiger Source selection

0: From PTPI pin

1: From PTCK pin

Bit 0

 PTCCLR

: PTM Counter Clear condition selection

0: Comparator P match

1: Comparator A match

This bit is used to select the method which clears the counter. Remember that the 

Periodic TM contains two comparators, Comparator A and Comparator P, either of 

which can be selected to clear the internal counter. With the PTCCLR bit set high, 

the counter will be cleared when a compare match occurs from the Comparator A. 

When the bit is low, the counter will be cleared when a compare match occurs from 

the Comparator P or with a counter overflow. A counter overflow clearing method can 

only be implemented if the CCRP bits are all cleared to zero. The PTCCLR bit is not 

used in the PWM Output, Single Pulse Output or Capture Input Mode.

Periodic Type TM Operation Modes

The Periodic Type TM can operate in one of five operating modes, Compare Match Output Mode, 
PWM Output Mode, Single Pulse Output Mode, Capture Input Mode or Timer/Counter Mode. The 
operating mode is selected using the PTM1 and PTM0 bits in the PTMC1 register.

Compare Match Output Mode

To select this mode, bits PTM1 and PTM0 in the PTMC1 register, should be set to 00 respectively. 
In this mode once the counter is enabled and running it can be cleared by three methods. These are 
a counter overflow, a compare match from Comparator A and a compare match from Comparator P. 
When the PTCCLR bit is low, there are two ways in which the counter can be cleared. One is when 
a compare match from Comparator P, the other is when the CCRP bits are all zero which allows the 
counter to overflow. Here both PTMAF and PTMPF interrupt request flags for Comparator A and 
Comparator P respectively, will both be generated.

Содержание BS66F340



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BS66F340

Kingston Technology DataTraveler Locker+ Generation 3 DTLPG3 Installation Manual preview
DataTraveler Locker+ Generation 3 DTLPG3
Бренд: Kingston Technology Страницы: 1623
WiebeTech TDKEX2 User Manual preview
TDKEX2
Бренд: WiebeTech Страницы: 4
garofalo EASY ROLL 170.S/2/PS User Manual preview
EASY ROLL 170.S/2/PS
Бренд: garofalo Страницы: 12
SanDisk DMS platform Brochure preview
DMS platform
Бренд: SanDisk Страницы: 4
TrekStor t-series Manual preview
t-series
Бренд: TrekStor Страницы: 100
Hama 104389 Operating Instructions Manual preview
104389
Бренд: Hama Страницы: 8
LaCie 301200U User Manual preview
301200U
Бренд: LaCie Страницы: 48
Raidon InTANK iR2775-S3 Quick Installation Manual preview
InTANK iR2775-S3
Бренд: Raidon Страницы: 2
LaCie STEV1000400 User Manual preview
STEV1000400
Бренд: LaCie Страницы: 26
Archos ARCFlash User Manual preview
ARCFlash
Бренд: Archos Страницы: 12
Palram Skylight Instructions Manual preview
Skylight
Бренд: Palram Страницы: 81
NEC NR-9300 User Manual preview
NR-9300
Бренд: NEC Страницы: 16
3Ware 9650SE-4LPME Installation Manual preview
9650SE-4LPME
Бренд: 3Ware Страницы: 50
SanDisk Computer Drive Quick Start Manual preview
Computer Drive
Бренд: SanDisk Страницы: 1
Far Group FARTOOLS BRICO WB 100 Manual preview
FARTOOLS BRICO WB 100
Бренд: Far Group Страницы: 8
Samsung T3 Installation Manual preview
T3
Бренд: Samsung Страницы: 6
Samsung T1 Troubleshooting Manual preview
T1
Бренд: Samsung Страницы: 7
Samsung MZ-5PA064 User Manual preview
MZ-5PA064
Бренд: Samsung Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды