Hologic DISCOVERY A Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 274

background image

Discovery QDR Series Technical Manual

3-37

Note: The PosLimitOffset and NegLimitOffset entries in the [AyMotor] section

of the SQDRIVER.INI file determine the motion limits relative to the
mechanical stops. If these entries are not present, or are zero, the motion
limits are set to the mechanical limits).

The program then changes the plot title to

PRESS ANY KEY TO CONTINUE

.

7. Press the

<Enter>

key and the program prompts.

For information about calibration parameters, see “Calibration Parameters AY”
on page 3-37.

8. Type

Y<Enter>

to accept the calibration values or

N<Enter>

to reject them.

3.4.4.2.1 Calibration Parameters AY
The motor_direction field determines whether the positive step direction is the reverse of
the direction of increasing encoder values ('0' if the direction is not reversed, '1' if it is).
This value is set from the corresponding parameter in the MOTOR_AY.PRO file and is a
constant for each motor (i.e., the direction of increasing encoder values must agree with
the system coordinates and the positive step direction is set by the wiring harness for the
stepper motor).

The eight calibrate_position fields are:

1)

1 (Tolerance). The

±

position tolerance, in encoder ticks, for absolute moves. The

calibration program sets this field to the value found in the corresponding
calibrate_position field in the MOTOR_AY.PRO file.

2,3)

2288,41187 (NumberOfSteps,StepDistance). The number of motors steps
corresponding to the step distance in microns. The ratio of these two numbers
determines the step size (41187/2288

≅

18 microns). The calibration program sets

these fields to the values found in the corresponding calibrate_position fields in
the MOTOR_AY.PRO file. Since these values are a property of the mechanical
design of the system, they should never change.

4,5)

209,61339 (NumberOfTicks,TickDistance). The number of encoder ticks
corresponding to the tick distance in microns. Again, it is the ratio of these two
numbers (61339/209

≅

293 microns) that determines the encoder calibration.

These numbers will generally change from calibration to calibration (although the
ratio should remain approximately the same).

6)

363 (EncoderOffset). The value subtracted from the encoder readback to set the
origin of motion. The origin of AY motion is the extreme right mechanical stop, so
this value should be the same as the first field below.

motor_direction=1

calibrate_position=1,2288,41187,209,61339,363,363,3750

pos_limit_position=984946

neg_limit_position=0

Update Driver INI-File [Y/N] ?

«
...
87
88
89
90
91
...
»

Содержание DISCOVERY A



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY A

Бренд: Walker Bay Страницы: 8

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Taurus Страницы: 24

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды