CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan. Please remember:
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
visit our website at www.holmesproducts.com for
information on how to order a new fuse. Follow the
below instructions to replace the fuse on the plug.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover down towards the prongs.
Note:
Ensure that fuse cover is completely open
before attempting to
remove fuse.
3. Remove fuse carefully by
using a small screwdriver
to pry the fuse out of the
compartment by the
metal ends of the fuse
(see Figure 2).
4. Place plug on a solid, flat surface. Insert new 5
Amp, 125 Volt fuse into fuse compartment and use
a small screwdriver to secure the metal ends of the
fuse into the compartment.
Caution:
Risk of fire. Replace fuse only with 5
Amp, 125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the
fuse.
6. Risk of fire. Do not replace attachment plug.
Contains a safety device (fuse) that should not be
removed. Discard product if the attachment plug is
damaged.
FAN CLEANING
• Always unplug the fan before cleaning.
• Do not allow water to drip on or enter into fan
housing.
• Be sure to use a soft cloth moistened with a mild
soap solution.
• Do not use any of the following as a cleaner:
gasoline, thinner, or benzene.
Clean the fan grill, housing and base with a soft, damp
cloth. DO NOT ATTEMPT TO REMOVE THE FAN BLADE.
Please use caution around the motor housing area. Do
not allow the motor or other electrical components to be
exposed to water.
FAN STORAGE
When storing your fan in the off season, it is important
to keep it in a safe dry location. It is important to protect
the fan head from dust. We strongly recommend using
the original box from purchase.
ASSEMBLY INSTRUCTIONS
Your Table Fan comes completely assembled and is
ready for immediate use. Carefully unpack your fan,
refer to the operating instructions and enjoy!
OPERATING INSTRUCTIONS
Step 1: Set fan on a dry, level surface.
Step 2: Please make sure the Speed Controls is in the
Off(0) position. Plug cord into any standard
120 volt AC outlet.
Step 3: The Speed Control Knob is located on the
back of the Fan Motor Housing. The speed is
adjusted by turning the Speed Control Knob
to the desired setting, 0-II-I.
ADJUSTMENT INSTRUCTIONS
VERTICAL ANGLE ADJUSTMENT – Loosen Tilt Adjustment
Knob, hold the fan base, and gently move the motor
housing up or down to the desired vertical angle.
Lastly, be sure to firmly tighten the Tilt Adjustment
Knob to keep the fan head in place.
OSCILLATION CONTROL – The oscillation control bar is
located on the top of the motor housing. Push the
control bar down for oscillation, pull up for operation in
a stationary position.
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
When using electrical appliances, basic safety
precautions should always be taken including the
following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the
instruction manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet.
4. Close supervision is necessary when any appliance
is used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has
been dropped/damaged in any manner. Discard
fan or return to an authorized service facility for
examination and/or repair.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do
not route cord under furniture or appliances.
Arrange cord away from traffic area and where it
will not be tripped over.
11. The use of attachments not recommended or sold
by the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or
leave exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all
parts properly in place.
17. This product is intended for household use ONLY
and not for commercial or industrial applications.
18. WARNING: To reduce the risk of electrical shock and
injury to persons, do not use in window.
19. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state
speed control device.
20. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product
from the outlet. Replace the fuse as per the user
servicing instructions (follow product marking for
proper fuse rating) and check the product. If the
replacement fuse blows, a short circuit may be
present and the product should be discarded or
returned to an authorized service facility for
examination and/or repair.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
C L E A N I N G / M A I N T E N A N C E
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
A
B
C
D
A. Fan Head
B. Motor Housing
(not visible)
C. Fan base
D. Tilt Adjustment
Knob
Figure 1
If you have any questions regarding your product
or would like to learn more about other Holmes
®
products, please visit our website at
www.holmesproducts.com. For inquiries regarding
recycling and proper disposal of this product,
please contact your local waste management
facility.
Figure 2
Metal ends
Fuse cover
Fuse
HAOF87BLZ-UC_15EM1.qxd:HAOF87-UC14EM1 16/1/15 4:58 PM Page 2