background image

Hochiki Europe (UK) Ltd – HE-PSU(4.0) Installation Manual 

Page 2 of 10 

2-3-0-997/ISS1/OCT07 

 

CONTENTS 

1. GENERAL........................................................................................................................2

 

2. POWER REQUIREMENTS .............................................................................................2

 

2.1 HE-PSU(4.0) Input/Output Electrical Ratings .............................................................2

 

2.2 Fuse Ratings ..............................................................................................................3

 

2.3 Batteries .....................................................................................................................3

 

3. INSTALLATION ...............................................................................................................3

 

3.1 Environmental Considerations....................................................................................3

 

3.2 Mounting ....................................................................................................................3

 

3.3 Connecting to the Input ..............................................................................................4

 

3.4 Connecting to the Outputs..........................................................................................4

 

3.4.1 Load Connections (Terminal Block).....................................................................4

 

3.4.2 Load Connections (Ribbon Cable).......................................................................4

 

3.4.3 Battery Connections ............................................................................................5

 

4. COMMISSIONING ...........................................................................................................6

 

5. MAINTENANCE...............................................................................................................6

 

6. MOUNTING .....................................................................................................................8

 

7. WIRING ...........................................................................................................................8

 

8. CABLE TERMINATION ...................................................................................................9

 

9. OPERATING INSTRUCTIONS ......................................................................................10

 

 

1. GENERAL 

The HE-PSU(4.0) is a combined power supply and battery charger designed to be used for fire alarm control 
and indicating equipment complying with EN54-2 and EN54-4. 
 

2. POWER REQUIREMENTS 

The HE-PSU(4.0) requires a mains power supply of 230V AC.  The maximum input current is 2 Amps.  
Mains frequency 50Hz. 
 

2.1 HE-PSU(4.0) Input/Output Electrical Ratings 

Input – 230V AC  
 
Load output - 

19V DC min (battery at minimum), 30 V DC max (mains on) max current 2.5 Amps + 1.5A 

for battery charging. 
 
Maximum ripple 800 millivolts 

 

Battery charging output - 26.4 VDC (at 40°C) 28.9 V DC (at -5°C) 1.5 Amps.  
 
Fault signals -  switched negative open collector (with respect to load positive) current limited 100mA max. 
 

 

Mains fail 

 

 

Battery disconnected (Low battery shut off voltage - 19 V (+/- 1 volt)) 

 

 

Battery low (Low battery warning voltage - 21 V (+/- 1 volt)) 

 

 

Earth fault 

 

 

Charger fault (high output to battery) 

 

 

Fail safe (any one of the above) 

 
These outputs are protected against short circuits. 

Содержание HE-PSU(4.0)











Отзывы: