background image

33

hobie.com

Storage and Transport

The best way to transport your boat is to purchase a trailer or roof rack from 

your dealer.  Using proper cradles that support the hull, the boat can be trans-

ported right side up. Straps can then be laid across the boat and tied to the 

bars.  Straps should be tight, but not so tight that they distort the shape of the 

boat.  Avoid using ratchet straps to prevent overtightening.

Pro Angler Roof Topping Technique

1

2

3

Be sure to first consult your car and roof rack owner’s manual 

to ensure that you comply with all of their recommendations, 

precautions and specifications.

Running a line or strap from the bow and stern of the boat to each bumper 

is required. If your bumpers do not have a gap to pass a rope around, look 

underneath. There should be a loop of metal, which is used by car transports 

such as tow trucks.

Many people like to use the scupper holes to tie the boat to the car. This 

helps prevent the boat from sliding back and forth or the tie-down rope from 

slipping off the boat. (This is an acceptable method for tying the boat down for 

transport.)

Содержание Mirage 360













































Отзывы: