HobbyZone Sport Cub S 2 Скачать руководство пользователя страница 6

Страница: 6 / 22

Sport Cub S 2

Transmitter Setup

IMPORTANT:

The installed receiver has been pro-

grammed for operation specifically in this aircraft.

To operate the SAFE system in this aircraft, set up
your optional DSM2/DSMX transmitter using the
chart below.

• SAFE Flight mode is selected using Channel 5

signal (high, middle, low)

• Panic Recovery mode is selected with Channel

6 signal (high, low)

IMPORTANT:

A transmitter with a 2-position

position 0 or position 2 flight modes. If possible
assign Channel 5 in your transmitter to a

3-position switch to operate all 3 flight modes
(refer to your transmitter manual).

Refer to your

transmitter’s manual for more information about transmitter setup.

Computerized Transmitter Setup

(DX6i, DX6, DX7S, DX8, DX9, DX10t and DX18)

Start all transmitter programming with a blank model (do a model reset), then name the model.

Set Dual

Rates to:

HIGH 100%

LOW 70%

DX6i

1. Go to the SETUP LIST MENU

2. Set MODELTYPE: ACRO

3. Set REVERSE: Gear Channel

4. Go to ADJUST LIST MENU

5. Set TRAVEL ADJ: Gear/Fmode (0)

🠉

100%; Gear/Fmode (1)

🠉

40%

6. Set FLAPS: Norm

🠉

100; LAND

🠉

100

7. Set MIX 1: ACT; Gear

🠉

Gear ACT, RATE D 0%; U + 100%, SW MIX, TRIM INH

Resulting

in:

The Gear and Mix switches operate the 3 SAFE modes

Gear 0; Mix 0 = Beginner Mode

Gear 1; Mix 0 = Intermediate Mode

Gear 1; Mix 1 = Experienced Mode

The Flap switch operates Panic Recovery.

Position 0, Panic Recovery off, Position 1 Panic Recovery on

DX7S
DX8

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set SWITCH SELECT: Change all to INH then TRAINER: AUX1, FLAP: GEAR

4. Go to the FUNCTION LIST

5. Set SERVO SETUP: Reverse AUX1

Resulting

in:

Flap/Gyro Switch operates the 3 SAFE modes (0 Beginner/1 Intermediate/

2 Experienced) The Trainer/Bind button operates Panic Recovery

DX6
DX9
DX10t
DX18

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Go to CHANNEL ASSIGN: click NEXT to go to Channel Input Config: Set GEAR: D

(DX10t: GEAR: A) Set AUX1: i (DX10t: AUX1: R-tip)

4. Go to the FUNCTION LIST

5. Set SERVO SETUP: Reverse AUX1

Resulting

in:

Switch D (DX10t: A) operates the 3 SAFE modes (0 beginner/1 intermediate/

2 Experienced) The Bind/I button (DX10t: R-tip) operates Panic Recovery

Channel 5 switch will only allow the use of

Non Computerized Transmitter Setup

(DX4e and DX5e)

Transmitter

SAFE

Mode

Switch

Panic

Recovery

Switch

SAFE

Flight

Modes

Supported

Throttle, Aileron, Elevator and Rudder in Normal Position

DX4e

(2pos switch)

ACT/AUX

switch

Trainer Button

2 Pos

Flight Mode

DX4e

(3pos switch)

CH 5

switch

Trainer Button

3 Pos

Flight Mode

DX5e

(2pos switch)

CH 5

switch

Trainer Switch

2 Pos

Flight Mode

DX5e

(3pos switch)

CH 5

switch

Trainer Switch

3 Pos

Flight Mode

Содержание Sport Cub S 2























Результаты поиска

Содержание Sport Cub S 2

Отзывы:

Похожие инструкции для Sport Cub S 2

Бренды по названию

Популярные бренды

HobbyZone Sport Cub S 2, Инструкция по эксплуатации

Результаты поиска

Содержание Sport Cub S 2

Отзывы:

Похожие инструкции для Sport Cub S 2

Бренды по названию

Популярные бренды