HobbyKing Plug-N-Fly Paramotor Скачать руководство пользователя страница 3

2

The HobbyKing™ Paramotor is extremely easy to fly due to its very gentle and stable flight 

characteristics yet once you are used to it, it will perform loops and rolls with ease. Due to the 

design, the huge high performance 2250mm wing opens quickly for easy launching and it will 

retain its shape even in turbulence. The single skin durable wing is made from 100% ripstop 

fabric and comes pre-rigged wiith tough nylon chords and ready to attach to the durable 

aluminum gondola.

There is a high level of prefabrication so assembly time is minimal and it is Plug-N-Fly so all 

you require is your own transmitter, receiver and battery. The Paramotor is fitted with a 

powerful 3530-1400KV brushless motor swinging a 10 x 4.7 propellor, it also has a 50 amp 

electronic speed controller with 5 amp BEC and 2 powerful 15kg high torque metal geared 

servos. A 3S lipoly battery is recommended and it can vary in capacity to suit different flying 

conditions. The

recommended flying weight is 1.6~2.0kg, in light wind conditions it is best to put a lighter 

battery in to keep near the 1.6kg weight. In windy conditions it is better to put a heavier battery 

in to fly around the 2kg mark. The undercarriage is easily removed for hand launching and 

catching and also for slope soaring.

If you fancy trying something a little different then the HobbyKing™ Paramotor is for you. Great 

fun to fly without being too challenging and it looks great in the air. Pre-assembled and Plug N 

Fly also means you can be airborne very quickly after taking delivery.

Features:

1 x 3ch or more computer transmitter with the ability to mix channels

and set control curves

1 x 3ch or more receiver

1 x 3S (11.1v) lipoly battery and charger

Type: Plug-N-Fly Paramotor

Parawing Span: 2250mm

Motor: 3530-1400KV brushless

Propeller: 10x4.7

ESC: 50amp

BEC: 5amp

Servos: 2 x 15kg high torque metal geared Flying Weight: 1.6~2kg

Recommended Battery: 3S lipoly (not supplied)

Specs:

Required:

• High performance parawing

• Plug and Fly format ( you only require a Tx, Rx and battery)

• High level of prefabrication for quick assembly

• Gentle flight characteristics, however it can perform loops and rolls

• Removable undercarriage for slope soaring etc

• Durable aluminum airframe

• Wide flying weight range (1.6~2kg)

Содержание Plug-N-Fly Paramotor


























Отзывы: