manualshive.com logo in svg

Hobbico Superstar 60, Руководство пользователя

Поделиться
Скачать
Hobbico Superstar 60 Скачать руководство пользователя страница 17

Prepare the engine mount

❏ 

27. Carefully trim off the molding braces from both

halves of the nylon adjustable engine mount. Attach
the two halves together and onto the firewall using
four 6-32 x 7/8” machine screws. Do not tighten the
screws completely at this time.

Install the throttle guide tube

❏ 

28. Roughen the outside of both plastic guide tubes

and clean with a paper towel dampened with rubbing
alcohol. This will help the glue stick to the tubes.
Install one of the tubes into the upper hole in the
firewall. Position the tube so that approximately 2”
protrudes out of the firewall. Mix 1/8oz. of 6-minute
epoxy and glue the guide tube into the hole in the
firewall and into the upper right slot inside
the fuselage as shown.

Drill the steering pushrod exit hole

❏ 

29. Drill a 5/32” hole into the firewall, 3/8” from

the bottom and 5/8” from the inside edge of the
fuselage side.

Install the steering guide tube

❏ 

30. Slide the remaining guide tube into the hole

you just drilled so that 1/2” protrudes. Mix up 1/8oz.
of 6-minute epoxy. Glue the tube into the hole and
into the 

lower left slot

inside the fuselage. Once the

glue has cured, trim off this tube so it is flush with the
firewall (Do not trim off the throttle tube).

Make “Z” bends on the wire

❏ 

31. Make a Z-bend at one end of both of the 1/16” x

19-3/4” wire throttle and steering pushrods. 

NOTE:

Hobbico offers pliers that easily make perfect
Z-bends (HCAR2000) see your hobby dealer.

Trim the steering arm

❏ 

32. Locate the black plastic steering arm. Hold the

arm in your hand so that the screw hole on the side is
facing you. Using a wire cutter, remove the left side of
the arm. It is not needed.

Install the steering wire

❏ 

33. Attach the “Z” bend of one of the wires into the

outside hole of the black plastic steering arm. Slide
the wire into the lower guide tube so that the steering
arm is against the firewall with the screw hole
facing forward.

17

Содержание Superstar 60





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды