How to drive
After running
How to operate the tool attachment
A
NTENNA
➊
Gently pull up the antenna
by hand. Never attempt to extend
the antenna by turning or
pushing the dial on the back of
the transmitter.
➋
Turn on the transmitter switch.
Throttle (left toggle control) - Move the truck forward by pushing
up, or reverse by pushing down.
Steering Wheel (right toggle control) - Steer the front tires left or
right by pushing the right toggle control.
By operating the toggle controls on both the right and left
simultaneously, the truck can move forward-right, forward-left,
reverse-right, or reverse-left.
☞
To run two R/C MicroSizers cars or PowerBrutes together,
each must be on a different frequency.
➊
Turn the winder on the back of the transmitter to store the
antenna. Do not force the antenna back inside the transmitter
by hand.
➋
Switch the transmitter off. Always turn the switch off when not
in use to extend your battery life.
☞
If the truck does not go
straight when pushing the left
toggle control up, move the
trim lever on the bottom of
the chassis to the left or right
to make adjustments.
O
N
/O
FF
S
WITCH
A
NTENNA
W
INDER
S
TRAIGHT
L
INE
T
RIM
C
ONTROL
T
HROTTLE
C
ONTROL
S
TEERING
C
ONTROL
➊
Press the transmitter’s
Action Activator button
to move the tool up
and down.
➍
When installing a motor,
make sure that the motor
contacts are in the proper
position as shown
Model Battery Care
Transmitter Battery Care
A rechargeable battery has been built in to the main body of the
model. Using the battery incorrectly will cause it to leak, rupture
or ignite. Follow these precautions:
·
If your R/C MicroSizers PowerBrutes has been unused for a long
period or you are charging its built-in battery for the first time,
the battery may not charge to full capacity. This does not
indicate battery failure. Recharging and running the model 4 or
5 times will gradually lengthen run times.
·
Fully discharge the battery by running the truck before recharging.
·
Charge the battery only when the truck is NOT running. To prevent
overcharging, never recharge a battery which has already been
fully charged. This will not increase running speed.
·
Recharge the battery only with the transmitter's built-in charger.
·
If the chassis becomes warm, let it cool before running again.
This product uses a NiCd battery. NiCd batteries are recyclable,
and a valuable resource. To dispose of the battery, remove it and
take it to a recycling center.
Always use AA alkaline batteries. If improper batteries are used
in the transmitter, they may become hot, leak and may rupture.
Follow these precautions:
·
Never use rechargeable batteries, such as NiCds, in
the transmitter.
·
Do not mix different types of batteries, or old and new batteries.
·
When changing batteries, replace ALL of the old batteries with
new ones.
·
Make sure the batteries are installed with the correct polarity
as shown in the battery compartment.
·
Do not charge or disassemble your transmitter batteries. Never
allow them to become hot or to burn. To avoid short-circuits,
avoid getting them wet.
·
If liquid from inside the batteries contacts your skin or clothes,
wash them with water. If leaked battery fluid gets into your eyes,
flush them immediately with cool water and seek medical
attention. Do not rub eyes.
·
You can race about 50 times with new AA alkaline batteries.
Important Battery Information
A
CTION
A
CTIVATOR
How to change the drive motor
➊
Pull off the heatsink
with your fingers.
➋
Pull out the motor.
➌
Install a new motor.
Optional motors (available separately) can be installed for higher performance.
Shaded area must
be toward the front
of the chassis.
H
EATSINK
