HNP Mikrosysteme mzr-11507 Скачать руководство пользователя страница 36

Страница: 36 / 68

8 Startup/shutdown of a mzr-pump

Operating manual mzr-11557 Ex

Technical data subject to change without prior notice!

Last update: March 2019

Nature of the delivered liquid

Flushing time [min]

Suitable flushing liquid

Oils, fats, plastifierss

15-20

isopropanol, ethanol, acetone,
benzine/petroleum ether

Solvents (polar + nonpolar)

5-10

isopropanol, ethanol

Other organic liquids

10-15

isopropanol , ethanol

Refrigerating and cooling agents

15-20

isopropanol, ethanol

Neutral water/y solutions

20-25

isopropanol, ethanol

Basic solutions

25-30

DI-water (deionized water)

Organic acids

30-40

isopropanol, ethanol

Weak mineral acids

25-30

DI- water

Strong mineral acids

35-45

DI- water

Strong oxidizing liquids

35-45

DI- water

Paints, varnishes, adhesives

50-60

not specified - for further information
please contact HNP Mikrosysteme.

table 14

Selection of the flushing liquid (solvent) and the duration of the flushing procedure depending on the
delivered liquid.

Warning

Please make sure that the pump components and particularly O-rings and

sealing are resistant to the employed flushing liquid (see table 15).

Shaft sealing

O-ring material

Flushing liquid

PTFE (Teflon

graphite-

reinforced

UHMWPE

FPM

(Viton

)

EPDM

FFPM

acetone

benzene

benzyl alcohol

butanol

dimethyl sulfoxide (DMSO)

ethanol

isopropanol

methanol

methylethylketone (MEK)

styrene

toluene

water

xylene

benzine/petroleum ether

oil / fine mechanics oil

Legend:

0 ... good suitability 1 ... suitability 2 ... conditional suitability 3 ... labile - ... not specified

table 15

Resistance of the sealing materials depending on the flushing liquid (solvent)

Содержание mzr-11507





































































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды