HMS Anybus IP30 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 12

HMS Anybus IP30 Скачать руководство пользователя страница 4

Installation

4 (12)

2

Installation

Caution

This equipment emits RF energy in the ISM (Industrial, Scientific, Medical)
band. Make sure that all medical devices used in proximity to this device
meet appropriate susceptibility specifications for this type of RF energy.

This product contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD prevention measures to avoid damage.

Make sure that you have all the necessary information about the capabilities and
restrictions of your local network environment before installation.

For optimal reception, wireless devices require a zone between them clear of
objects that could otherwise obstruct or reflect the signal. A minimum distance of
50 cm between the devices should also be observed to avoid interference.

The Anybus WLAN Access Point IP30 can be mounted on a standard DIN rail or
screw-mounted directly onto a flat surface using the included wall mounting kit.

Anybus

®

WLAN Access Point IP30 Startup Guide

SP2382 EN 1.1

«
...
2
3
4
5
6
...
»

Содержание Anybus IP30













Отзывы:

Нет отзывов