HME Clear-Com 104G070 Скачать руководство пользователя страница 9

Страница: 9 / 18

TRANSCEIVERS AND CONNECTING A TRANSCEIVER TO THE BASE STATION

The EQUIP wireless intercom supports up to four remote transceivers�
EQUIP transceivers connect directly to the EQUIP base station via an Ethernet cable (CAT5/6 cable

with RJ45 connectors)� Transceivers are powered from the base station and can be placed up to

500 feet (152 m) from the base station�

Note:

Do not connect the transceiver to a network port/IP switch� This can result in a system fail-

ure or component damage�

Remote

XCVR 4

Remote

XCVR 3

Remote

XCVR 2

Remote

XCVR 1

Ethernet

DC +

DC -

GND

Micro

USB

J200

J600

J201

J800

J801

J802

J805

J804

J803

J2003

J3000

J4501

J4500

J1400

J3200

J3400

J3600

J3800

Serial

Debug

USB

J?301

J?300

Base Station

opened

PCBA

To NETWORK ROUTER

For CLOUD CONNECTION

48 V

BASE STATION

POWER SUPPLY

To REMOTE

TRANSCEIVER REAR

To WALL

OUTLET

TRANSCEIVER

Front View

BASE STATION

Partial Inside View

This Way

DC+

GND

DC-

To REMOTE

TRANSCEIVER REAR

Fig. 9

The EQUIP LEDs on the front of the transceiver shows which port the transceiver is

connected to on the base station (1 in this example)� The green center LED indi-

cates the transceiver is powered on and functional�

Fig.

Содержание Clear-Com 104G070


















Результаты поиска

Содержание Clear-Com 104G070

Отзывы:

Похожие инструкции для Clear-Com 104G070

Бренды по названию

Популярные бренды

HME Clear-Com 104G070, Руководство по установке

Результаты поиска

Содержание Clear-Com 104G070

Отзывы:

Похожие инструкции для Clear-Com 104G070

Бренды по названию

Популярные бренды