background image

INSTRUCTION MANUAL

INSTRUCTION

E05253-E11020-00

September 2021

Ver. 3-1.01

Thank you for your purchase of BOOST CONTROLLER.

・ This manual indicates items that require attention in order to install this product 
   safely and lists precautions to avoid any possible damage and/or accidents.
・ This product was designed based on installation onto a specific factory vehicle
  or a vehicle using other HKS products. The performance and/or safety cannot be 
   guaranteed if this product was installed onto other inapplicable vehicles.
・ Contact HKS dealer for any lost parts, replacement, and this manual.
・ HKS will not be responsible for any damage caused by incorrect installation and/or 
   use of this product.
・ This product works only with a vehicle with DC12V negative ground.
・ The specifications of this product are subject to be changed without notice.
・ This manual is subject to be revised without notice.
・ When removing factory parts, refer to the factory manual. The factory manual must
  be purchased if you don't have it.

2. Safety Precaution 

   

 The following precautions for use of this product are to prevent possible
accidents and/or injuries and for proper use.

ー 1 ー

ー 2 ー

VIITS BOOST CONTROLLER
V I I T S - E L 0 0 1

Boost up of turbocharged vehicle
ABARTH595 COMPETIZIONE [31214T]

Product

Code Number

Use

Application

1. Introduction

3. Product Features

1. Stop the engine of the vehicle and Disconnect the cable terminal from the

 

      negative terminal of the battery.
2. Install the 

BOOST CONTROLLER

 main unit in an arbitrary place.

  ・ Avoid the following places.
   - Places where the temperature becomes high like the engine body.
   - Places where direct water is applied.
  ・ Confirm that the connection harness reaches the pressure sensor.
  ・ When using double sided tape, clean the surface to be pasted, paste it, and use 
      tie wraps together.
    When pasting with double-sided tape only, it is dangerous when it peels off due 
      to aged deterioration.
3. Connect the 

BOOST CONTROLLER

 main unit and Connector for main unit.

4. Disconnect Manufacturer's original connector from Pressure sensor, and wire 
      the connection harness of 

BOOST CONTROLLER.

  ・ Longer harness is channel 1, shorter one is channel 2.
  ・  In factory default settings, the boost-up data in channel 1 and channel 2 are
   same.
  ・  Please be aware of the channel order during modifying boost-up data by
   Power Editor EasyWriter software.
5. Lock the connection harness of 

BOOST CONTROLLER

 with tie wrap so as

   not to hinder 
      the running of the vehicle.
  ・ Places where the temperature becomes high like the engine body.
6. After confirming that all connectors are correctly connected, connect the cable

 

      terminal to the negative terminal of the battery.
7. Turn the ignition on and check that the LED of the 

BOOST CONTROLLER

 main 

   unit lights up.
  ・ Even if the ignition is turned on, if the LED does not light up, poor contact of the 
      connector may be considered.

Connection harness

BOOST CONTROLLER

 main unit

Pressure sensor

Pressure sensor

Operation confirmation LED

Lighting off : Power off
Lighting on : Power on
1 blink   : ch1 data is broken
2 blinks : ch2 data is broken
3 blinks : ch1/ch2 data is broken

When the LED flashes the boost 
will not rise, it will behave like a 
normal vehicle.

Manufacturer's 

original connector

5. Installation procedure  

・ By connecting this product between Pressure sensor and Manufacturer's 
   original connector, boost can be easily raised.
・ Even after installing this product, you can return to the normal state by 
   connecting the "return connector" instead of the 

BOOST CONTROLLER

 main

  unit.
・ You can change the data for the boost up of the main unit by connecting to the 

   

personal computer with USB harness included in the product and using Easy Writer 

   for Power Editor.
  Easy Writer for Power Editor is available for free on the HKS website.

1pc.

 Connection harness

1pc.

 

BOOST CONTROLLER

1pc.

USB harness

4. Parts List

1pc.

 

Connector to return to 

normal

2pc.

Tie wrap (large)

2pc.

 Double-sided tape

1pc.

Instruction Manual

Connector for connecting USB harness

・ Make it stuck with tie wraps or the like so that 
  it will not be shaken during driving

Connector for main unit

Channel 1

Channel 2

Indicates risk of serious injury and/or possible death.

Indicates risk of serious injury or property damage.

WARNING :

CAUTION :

● Make sure to work on the vehicle in a well-ventilated area to prevent possible 
    explosion or a fire. 
● Make sure to hold connectors when removing them to avoid possible damage to 
    other electronics parts and/or a fire caused by disconnection or a short circuit.
● Stop using the product if any unusual situation is noticed.  Consult the dealer 
    immediately.  Failure to do so may cause an electric shock, burn out, or damage 
    to the vehicle.
● Make sure to work on the vehicle in area where a vehicle can be parked safely.

WARNING

CAUTION 

● Do not install this product by yourself.  
● Do not modify, disassemble, and/or remodel the product and attached parts to 
    avoid any damage to the unit and/or harness. 
● To avoid possible malfunction and damage to the engine, install the unit away

 

  from excessive heat or water/moisture. 
● Make sure all connections and wiring are not disconnected, short circuited, 
  or incorrect.  If so, it may cause an electric shock, burn out, or damage to the 
    vehicle. 
● If any unusual noise, scents, and/or vibrations are noticed, consult the dealer

 

  immediately.
● If any unusual noises, scents, and/or vibrations are noticed while driving, please 
    refer to a factory repair manual.
● Confirm the following before reading the ECU data with this product:
  ・ The ECU is a factory standard.
  ・ Data on the ECU is not modified. 
● Desorption of the connector, please go Always hold the connector.
    ・ If you pull the cable, there is a possibility of disconnection.
● Before an automobile inspection and/or repair,It is necessary to remove this 
    product.
● Daily maintenance on the vehicle is the responsibility of the owner.

Manufacturer's 

original connector

4pc.

 Tie wrap (small)

(Male 4pin Connector)

(Male 3pin Connector)

(Female 4pin Connector)

(Female 3pin Connector)

BOOST CONTROLLER for ABARTH595

取扱説明書

E89671-T41010-00

2018.01発行

Ver. 3-1.01

BOOST CONTROLLER for ABARTH595

Отзывы: