HKS 12001-AT005 Скачать руководство пользователя страница 31

Страница: 31 / 81

HKS GT SUPERCHARGER SYSTEM /LS460

- 30 -

730mm

5. INSTALLATION OF TRACTION FLUID HOSE

NOTE

The internal components of the Supercharger Assembly are very precise and
exact; foreign objects mixed with Traction Fluid can lead to damage to the
Supercharger Assembly. Do not allow foreign objects to mix with the Traction
Fluid.

○

Cut the Hose Assembly 10mm at 730mm from the
fluid filter side.

※

Make sure to cover the hose end to prevent

foreign objects from entering to the hose.

○

Cut the Corrugated Tube 15mm to 300mm in length.
Install the cut Corrugated Tube to the end of the Hose
Assembly 10mm.

○

Install the Silicone Hose 50mm L=20 to the Fluid Filter.

・

Hose Assembly 10mm

・

Corrugated Tube 15mm

―

Traction Fluid Flow

―

・

Silicone Hose 50mm L

＝

Содержание 12001-AT005


















































































Результаты поиска

Содержание 12001-AT005

Отзывы:

Похожие инструкции для 12001-AT005

Бренды по названию

Популярные бренды

HKS 12001-AT005, Руководство по установке

Результаты поиска

Содержание 12001-AT005

Отзывы:

Похожие инструкции для 12001-AT005

Бренды по названию

Популярные бренды