LINEAR 9 1.0
5
●
8
Preset
Use the Preset selection button to call up factory presets or a user preset
you can configure via the remote DSP CONTROL software. Tap the select
button once to scroll through Presets 1 through 4.
A separate manual explains how to program the four remote user presets.
You will find it on the LINEAR 9 download page at www.hkaudio.com.
A look at the presets:
L9 210 LTA
L9 110 XA / L9 112 XA L9 118 Sub A / L9 118 Sub BA
Remote
1
2
3
4
Remote
1
2
3
4
Remote
1
2
3
4
Flat
Low Cut
Monitor
Front
Cardioid 1:1
Cardioid 2:1
Remote
1
2
3
4
Remote
1
2
3
4
Remote
1
2
3
4
Flat
Low Cut
Monitor
Front
Cardioid 1:1
Cardioid 2:1
Remote
1
2
3
4
Remote
1
2
3
4
Remote
1
2
3
4
Flat
Low Cut
Monitor
Front
Cardioid 1:1
Cardioid 2:1
1
Stand Alone
Flat
Front
2
Cluster (2)
Monitor
Cardioid 1:1
3
Cluster (3)
Low Cut
Cardioid 2:1
4
Remote (to access stored settings via the remote
HK Audio DSP CONTROL software)
Factory presets: LINEAR 9 210 LTA
Stand Alone
for a single L9 210 LTA (per side)
Cluster (2)
for two connected L9 210 LTA units
Cluster (3)
for three connected L9 210 LTA units
Factory presets: LINEAR 9 110 XA • LINEAR 9 112 XA
Flat
Delivers linear response across the full frequency range
Monitor
Optimized to dampen the extra bass generated by floor
coupling when you set a speaker on its side for use as a
monitor
Low Cut
A high-pass filter optimizes the unit for use as a mid/high
unit paired with the L9 118 Sub A/L9 118 Sub BA
Factory presets: LINEAR 9 118 Sub A • LINEAR 9 118 Sub BA
Front
Standard operating mode for a forward-facing subwoofer
Cardioid 1:1
For cardioid setups with one forward-facing L9 118 Sub A/
L9 118 Sub BA; see section 4.2 for more on this
Cardioid 2:1
For cardioid setups with two forward-facing L9 118 Sub A/
L9 118 Sub BA; see section 4.2 for more on this
Factory presets 1 to 3 address the speaker only and not the DSP Out.
Heads up: If you are operating the speaker in a network connected to
the remote DSP CONTROL software, you can configure the DSP Out
independently even when using factory presets 1 to 3. To learn more
about this, consult the separate DSP CONTROL manual. You will find it
on the LINEAR 9 download page at www.hkaudio.com.
The Remote Preset
Remote
This lets you call up a user preset that you previously stored
via DSP CONTROL for the speaker as well as for the DSP
Out. The speakers does not need to be connected to the
remote software to do this.
The remote preset's default setup is identical to factory preset 1 (Stand
Alone/Flat/Front).
You can access the following DSP functions via the remote DSP CONTROL
software and save your settings in user presets:
Fully parametric 10-band EQ with variable filter characteristics for each
frequency band, high-pass and low-pass filters with variable filter
characteristics, Limiter, Delay, Polarity, Level, and Mute
You can configure these parameters separately and independently for the
speaker and its DSP Out.
Screenshot of the remote DSP CONTROL software. You can download this software free of charge at the
LINEAR 9 product page at www.hkaudio.com. The speaker and DSP Out parameters are identical, but
the powerful onboard DSP lets you configure each set independently.
●
9
Power
This rocker switch turns the power on and off. Set it to Power to turn the
electronic components on and to Off to disconnect them from the mains
power supply. The Power switch does not affect the Powercon Link port.
See section
●
12
below for more on this.
●
10
Power-LED
This LED lights up green when the electronic components are getting mains
power.
●
11
Mains Input
Use the factory-included Powercon mains cord
to connect this socket to a power outlet. Insert
the push-pull connector and turn it clockwise
to make sure the Powercon cord engages and
locks. To unlock it, pull the Powercon plug's
locking mechanism towards the cable and turn it
counterclockwise.
Leave enough space for proper ventilation!
LINEAR 7
118 Sub A
MADE IN GERMANY
Power
Auto Sleep
On
Off
+6 dB
–6 dB
0 dB
Input
L
R
DSP Out
Thru
Gain
Serial No.
Mains Input
100-240 V~ 50-60 Hz
1.9 A @ 1/8 output power
Link
100-240 V~ 50-60 Hz
max. 10 A
Caution: Risk of electric shock! Do not open!
Refer servicing to qualified service personnel.
Attention: Risque de choc élèctrique –
ne pas ouvrir!
HK Audio is a brand of Stamer Musikanlagen GmbH
Magdeburger Str. 8 • 66606 St. Wendel • Germany
Power
Lock
Lock
1
5
2
1
2
3
4
4
9
11
12
10
13
●
12
Link
This socket can power up to three additional LINEAR 9
speaker cabinets. Hardwired to the Mains Input, it is not
affected by the Power switch setting. The Link circuit
goes live the moment you connect the Mains Input to
a power source. This is why you must make sure all
downstream devices are switched off before you connect
them to the Link port.
• English
• Deutsch
Leave enough space for proper ventilation!
LINEAR 7
118 Sub A
MADE IN GERMANY
Power
Auto Sleep
On
Off
+6 dB
–6 dB
0 dB
Input
L
R
DSP Out
Thru
Gain
Serial No.
Mains Input
100-240 V~ 50-60 Hz
1.9 A @ 1/8 output power
Link
100-240 V~ 50-60 Hz
max. 10 A
Caution: Risk of electric shock! Do not open!
Refer servicing to qualified service personnel.
Attention: Risque de choc élèctrique –
ne pas ouvrir!
HK Audio is a brand of Stamer Musikanlagen GmbH
Magdeburger Str. 8 • 66606 St. Wendel • Germany
Power
Lock
Lock
1
5
2
1
2
3
4
4
9
11
12
10
13
