Hiwin 25.12345 Скачать руководство пользователя страница 53

Страница: 53 / 64

Appendix 1: Accessories and spare parts

Assembly Instructions

Linear Tables HT-L

HTL-01-0-EN-1905-MA

Fig. 11.11

Magnetic strip

Suitable for linear table

Article number (7.5 m)

HT150

25-001195

HT200

25-001195

HT250

25-001196

11.9 Magnetic strip

The magnetic strip holds down the cover strip and is available in a length of 7.5 m.

Table 11.9

Article numbers for magnetic strip

Suitable for linear table

Cylinder-head screw

Article number

HT100

DIN 7984 M3 × 5

25-001203

HT150

DIN 912 M4 × 6

25-001204

HT200

DIN 912 M4 × 6

25-001205

HT250

DIN 6912 M5 × 8

25-001206

11.10 Cover strip deflection

The cover strip deflection set consists of the following parts:

8 × cover strip guide

16 × cylinder-head screw

Each carriage requires one cover strip deflection set.

Fig. 11.12

Cover strip deflection

Cylinder-head screw

Cover strip guide

Table 11.10

Cover strip deflection set article numbers

Содержание 25.12345

































































Результаты поиска

Содержание 25.12345

Отзывы:

Похожие инструкции для 25.12345

Бренды по названию

Популярные бренды

Hiwin 25.12345, Руководство по сборке

Результаты поиска

Содержание 25.12345

Отзывы:

Похожие инструкции для 25.12345

Бренды по названию

Популярные бренды