manualshive.com logo in svg

Hitachi WH10DL, Технические данные и руководство по обслуживанию, Страница: 22 / 31

Поделиться
Скачать
Hitachi WH10DL Скачать руководство пользователя страница 22

-19-

•

 

Reassembly of the hammer assembly

Silicone rubber application area
(diagonally shaded area)

Housing (A)

3. Reassembly of housing (A). (B) set

(1) Apply silicone rubber (THREEBOND 1211) to the diagonally shaded areas in the following figure before

mounting the parts to housing (A).

(2) Pay attention to the following when mounting magnet (G).

• When mounting the Dust Guard Fin 

[24]

 to Magnet (G)

 [23]

, fit the protrusion of the Dust Guard Fin

[24]

 in the notch of Magnet (G) 

[23]

.

• Mount the side yoke to Magnet (G) 

[23]

 so that the flange of the side yoke faces outward.

(3) Mount a unit of the Hammer Case 

[7]

, Ring Gear 

[21]

 (including the Armature and Pinion Set 

[22]

),

Magnet (G) 

[23]

, Dust Guard Fin 

[24] 

and Switch (W/Controller and Tube) 

[34]

 into housing (A).

(4) Pay attention to the following when mounting.

• Mount the Hammer Case 

[7] 

to the housing so that the protrusion of the Hammer Case 

[7]

 (for

locking) contacts the concave portion of the housing as shown in the following figure.

• Check that the Hammer Case 

[7]

 is mounted to the housing properly. If the Hammer Case 

[7]

 is not

fitted in the specified groove of the housing or the rib of the Ring Gear 

[21]

 is not perpendicular to the

rib of the Hammer Case 

[7]

, remount the Hammer Case 

[7]

 properly. Be sure to mount the Hammer

Case 

[7]

 to the housing properly to prevent slipping off in the axial direction.

(5) Apply silicone rubber (THREEBOND 1211) to housing (B) at the same position as housing (A). Mount

housing (B) and secure it with the nine Tapping Screws (W/Flange) D3 x 16 (Black) 

[28]

. Wipe off

silicone rubber (THREEBOND 1211) protruded from the housing with a cloth.

    •

 

Reassembly of housing (A). (B) set (1)

Inner cover rib

Hammer case rib

Содержание WH10DL
































Отзывы:

Нет отзывов