background image

 

ELECTRICAL WIRING 

3. ELECTRICAL WIRING

Tools and Instruments 

 

One set of wiring tools, 

electrical tester (Clamp meter). 

Schedule Check 

 

Confirm that the field selected 

electrical  components  (main  power  switch, fuses, 
wires,  conduit  connections,  wire  terminals)  are 
properly  selected  and  ensure  that  they  comply 
with national  and  local  codes.  It  is  recommended 
that the main power switch be locked at the OFF 
position,  to  prevent  against  accidental  supply  of 
the power during unit servicing. 

Service  Panel 

 

Access  to  the  magnetic  switch 

box  is  provided  from  the  service  panel,  which  is 
fixed  with  screws  (see  the  panel  location  in  the 
Operation Instructions.) 

3.1 Main Power Wiring Procedures 

Confirm that electrical power is not being supplied 
to  the  installation  location  prior  to  any  electrical 
installation work. 

1. Install the field-supplied main switch box at the 

properly selected location. 

2. Install conduit connectors in the hole for power 

wiring (knockout holes). 

3.  Lead  the  main  power  wires  and  the  earthing 

wire  through  the  connector  to  the  screw 
terminals  for  main  power  and  earthing  in  the 
magnetic switch box. The  neutral  wire to  220V   
power  supplies  should  also  be  led  through  the 
connector.  Firmly  connect  the  wires  with  wire 
terminals  to  the  unit  screw  terminals  R(L1), 
S(L2)  and  T(L3)  for  220V  power  supplies 
according to Fig. 6 or the wiring label attached 
to the magnetic switch box. 

 

A  scroll  compressor  is  equipped.  Because  that 
the  rotation  direction  of  the  orbiting  scroll  of  the 
HITACHI  scroll  type  compressor  is  fixed, 
therefore  a  reverse  &  single  phase  sequence 
protection  relay  is  equipped  in  this  unit.  If  each 
phase R, S or T of the power source is incorrectly 
connected,  the  compressor  does  not  start  due  to 
the  activation  of  the  reverse  &  single  phase 
sequence  protection  relay.  Therefore,  in  order  to 
check the correct wiring connection, the utilization 
of  a  phase  sequence  indicator  is  recommended 
when  the  unit  is  started  after  installation  of  the 
unit. 

(1)  If  the  phase  is  wrong,  exchange  two  of  the 

three  wires  connected  from  the  main  power 
source  to  the  main  terminals  of  the  unit  as 
indicated  with dotted lines, and then check the 
rotation  direction  of  the  phase  sequence 
indicator  once  again.  Do  not  exchange  the 
wires  in  the  unit  in  order  to  protect  the 
compressor against the reversal rotation. 

 

           

R

S

T

Unit Side

 

(2) Do not operate the compressor by depressing 

the  button  of  the  magnetic  switch  for  the 
compressor. 

A  three-phase  condenser  fan  motor  is  equipped; 
therefore,  the  fan  motor  rotation  should  be 
checked. Interchange two of the three main power 
source  wires,  if  incorrect  rotation  is  detected 
during initial start-up. 

3.2 Control Wiring 

Install  the  optional  room  thermostat  at  a  suitable 
location  in  the  space  to  be  air-conditioned. 
Connect  the  control  wires  between  the  unit 
terminals  and  the  thermostat  terminals  according 
to Fig. 6 or the wiring label.   

 

Fig. 6. Field Wiring Connection

Terminal

Main Power

L2

S

Earth Terminal

Wiring

Power

Main

(Field Supplied)

Switch

Main
Power 

SL

L1

R

Control

(Utilize Connectors

Five (5) Wires for
Cooling Operation

Terminal

Circuit

L3

T

A

D

B

F

E

A,B,D,E and F)

Room Thermostat

Unit

(Field Supplied)

 

          Fig. 6. Field Wiring Connection 

 

Содержание RUA-13AT3S

























Отзывы: