background image

Make sure air tightness test is performed.

Refrigerant R410A is non-flammable, non-toxic, and odorless, and may produce toxic gases when exposed to

open  flame.  Since  this  refrigerant  gas  is  heavier  than  air,  it  may  result  in  lack  of  oxygen,  thereby  leading  to

breathing difficulties when the area near the ground is filled with this gas. If that's the case, please turn off the

main switch immediately, cut off the power supply, and open the doors and windows for ventilation. Put out any

open  flame,  and  contact  your  service  dealer.  Performing  leak  detection  and  gas  tightness  test  with  oxygen,

acetylene or other flammable and toxic gases may cause explosion, so nitrogen is recommended for this test.

The standards for safe refrigerant leakage in construction and system operation are determined based on local

regulations or standards.

Use ELB with medium or higher sensing speed (ELCB with an operating time of 0.1 seconds or less), or

electric shock or fire may arise.

For installation, the refrigerant piping must be firmly connected before the operation of compressor. For repair,

the refrigerant piping must be moved, handled and removed after the stop of compressor.

Please don't short-circuit the protective device (e.g., 

the 

pressure switch, etc.) during operation, since this

may

 

cause fire or explosion.

Do not use any sprays such as insecticide, lacquer, hair spray or other flammable gases within approximately 

one (1) meter from the system.

If the earth leakage breaker (ELB) is frequently activated, please stop the system and contact your local dealer 

or customer services.

Make sure the ground wire is securely connected. The improper grounding of machine may lead to electrical 

failure. Please don't connect the ground wire to gas pipes, tap water pipes, lightning rods or phone ground 

wires.

Make sure there are no flammable materials around during brazing operation. Please wear leather gloves to 

prevent frostbite when filling refrigerant.

Prevent rats or other small animals damaging the wiring and electrical components. Bitten unprotected parts 

may cause a fire.

Firmly fix the connection wires. The external force of terminal may result in looseness of terminal that may 

cause a fire.

Make sure the air conditioner is installed with enough strength of fixation; otherwise, the air conditioner may 

fall or topple over, which may bring about machine damage or personal injury.

Please follow the installation instructions and related regulations and standards for electrical construction; 

otherwise, electrical failure or fire may occur due to inadequate capacity or inconsistent specifications. 

Neve

r

 fail to use specified wiring and select correct wiring, since failure to do so may cause electrical failure or 

fire.
Please make sure the outdoor unit is not covered with snow or ice before use.

Please don't perform installation works such as refrigerant piping connection, drain pipe connection, and 

wiring connection. Violations may result in system leakage, electrical failure or fire. In the case of fire, please 

turn off the power immediately; please don't touch electrical parts with the hands, or electric shock may arise. 

Do not pour water into the indoor or outdoor unit. This machine is an electric product that may develop serious 

electric failure when exposed to water.

Do not open the service cover of indoor or outdoor units without turning OFF the main power supply; 

otherwise, this may bring about serious safety accident.

Do not touch or adjust safety devices inside the indoor or outdoor units. If they are touched or readjusted, 

serious accident may arise.

Refrigerant leakage may bring about oxygen deficit-induced respiratory difficulty. In case refrigerant leakage is 

detected, please turn off the main switch immediately, extinguish any naked flame, and contact service dealer.

DANGER

WARNING 

Please turn off power supply as soon as possible when a fire breaks out.

Please don't touch electrical components since this may result in electric shock.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, 

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or 

instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall 

not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

The A-weighted emission sound pressure don't exceed 70 dB(A) .

Содержание RPIZ-0.8HNDTS1Q





























Отзывы: