Hitachi RPFC-2.0TNE1NH Скачать руководство пользователя страница 7

Operation Manual

 Special Remarks 

 Trouble Shooting

If drain water overflows from indoor unit, stop the operation and contact your dealer.

If you smell or see white smoke coming from the unit, turn OFF the main power supply and contact

 

your dealer.

1. If Trouble Still Remains ...

   

      (1) Unit Model Name

      (2) Content of Trouble

2. No Operation

Check whether the SET TEMP is set at the correct temperature.

CAUTION

5

3 minutes protection after compressor stop

    

To protect compressor, it will be to be continue off for at least 3 minutes once it has stopped.

5 minutes protection

Cooling operation

Heating operation

Anti-freezing function during cooling

When the temperature of the air from the indoor outlet is too low, the unit will run for some time under the 

    fan mode, to avoid frost or ice forming in the indoor heat exchanger.

Cold air prevention

Defrosting

Blowing out the residual heating air

Compressor

 

must

 

run 

at least for 5 minutes once it starts running

In

 

this

 

5

 

minutes

compressor

 

will

 

not

 

stop

 

even

 

if

 

the

 

room

 

temperature

 

reaches

 

the

 

set

 

point

 

unless

 

you

 

use

 

remote

 

control

 

switch

 

to

 

turn

 

off

 

the

 

unit

 

(

all

 

indoor

 

unit

 

can

 

be

 

turned

 

off

 

by

 

user

).

The

 

fan

 

of

 

the

 

indoor

 

unit

 

will

 

never

 

stop

 

running

 

in

 

cooling

 

operation

It

 

remains

 

running

 

even

 

if

 

the

compressor

 

stops

 

working

.

Heating

 

capacity

 

depends

 

on

 

external

 

factors

 

as

 

outdoor

 

unit

 

temperature

Heating

 

capacity

 

might

 

decrease

 

if

 

outdoor

 

ambient

 

temperature

 

is

 

too

 

low

In

 

several

 

minutes

 

after

 

the

 

heating

 

mode

 

is

 

started

the

 

fan

 

of

 

the

 

indoor

 

unit

 

will

 

not

 

run

 

until

 

the

 

heat

 

exchanger

 

of

 

the

 

indoor

 

unit

 

reaches

 

a

 

certain

 

temperature

 

to

 

prevent

 

cold

 

draft

.

When

 

the

 

outdoor

 

temperature

 

is

 

too

 

low

frost

 

or

 

ice

 

may

 

form

 

on

 

the

 

outdoor

 

heat

 

exchanger

reducing

     

heating

 

performance

When

 

this

 

happens

a

 

defrosting

 

system

 

of

 

the

 

air

 

conditioner

 

will

 

operate

At

 

the

 

same

 

time

 

the

 

fan

 

in

 

the

 

indoor

 

unit

 

stops 

(

or

 

runs

 

at

 

a

 

very

 

low

 

speed

 

in

 

some

 

cases

), 

to

 

prevent

 

cold

 

draft

After

 

defrosting

 

is

 

over

the

 

heating

 

operation

 

and

 

fan

 

speed

 

restarts

.

Auto

 

restart

 

from

 

Power

 

Break

When

 

air conditioner is stopped during

 

normal

 

operation

the

 

fan

 

motor

 

will

 

run

 

with

 

low

 

speed

 

for

 

a

 

while

 

to

 

blow out

 

the

 

residual

 

heating

 

air

.

When

 

the

 

power

 

supply

 

is

 

recovered

 

after

 

power

 

break

all

 

presets

 

are

 

still

 

effective

 

and

 

the

 

air conditioner

 

will

 

run

 

according

 

to

 

the

 

previous

 

setting

.

If  the trouble still remains even after checking the following, contact your 

dealer and inform them of the 

following

 

items

.

Содержание RPFC-2.0TNE1NH

























Отзывы: