manualshive.com logo in svg

Hitachi RAM-68NP3B, Руководство по обслуживанию, Страница: 68 / 79

Поделиться
Скачать
Hitachi RAM-68NP3B Скачать руководство пользователя страница 68

LD351

 

13 times blink

EEPROM reading error

LD351

 

8 times blink

Communication error between micon

LD351

 

9 times blink

Indoor unit type mismatch error

LD352

 

1 time blink

LD351

 

Lit

OH thermistor abnormal

LD352

 

2 times blink

LD351

 

Lit

DEF(Hex) thermistor abnormal

Normal

Secure the connection of OH 

thermistor connector

Please replace DEF thermistor.

Please replace OH thermistor.

Please replace Main PWB.

Please re-connect DEF thermistor.

Is OH thermistor connector connected properly?

LD301 also 13 times blink

Is DEF thermistor connector connected properly?

Is OH thermistor wire worn out or short circuit?

Normal

Is DEF thermistor wire worn out or short circuit?

Yes

Abnormal

Yes

Yes

Yes

Yes

No

No

No

No

No

Are CN21,CN22 connectors inserted properly?

Yes

Normal

Please check refrigerant cycle.

(Assuming refrigerant leak occurs)

No

Normal

Abnormal

Abnormal

Abnormal

Abnormal

Normal

If not recovered after check the

cycle, please replace the Main PWB.

(Thermistor detection circuit abnormal) 

Secure the insertion of CN21,CN22 connectors.

Please exchange Main PWB.

(Microcomputer or EEPROM might be broken)

Please replace both Main PWB and Inverter PWB.

Wrong type (not multi type) of indoor unit is  

connected with the outdoor unit. Look again carefully. 

Please confirm the number of time of LD351 blinks?

Please replace Inverter PWB. If still NG after

(Microcomputer or EEPROM might be broken)

replace Inverter PWB, replace Main PWB.

Содержание RAM-68NP3B
















































































Отзывы:

Нет отзывов