Hitachi RAK-60NHA1 Скачать руководство пользователя страница 6

– 6 –

 

 

 

 

 

   

 

   

 

 

˚

CH

RESET

˚

CH

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

REMOTE CONTROLLER

  This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is controlled 

electronically, the range of control may be shorter.

 

This unit can be 

fi

 xed on a wall using the 

fi

 xture provided. Before 

fi

 xing it, make sure the indoor unit can be controlled 

from the remote controller.

  Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission 

capability.

  After new batteries are inserted into the remote controller, the unit will initially require approximately 10 seconds to 

respond to commands and operate.

 

Signal emitting window/transmission sign

  Point this window toward the indoor unit when controlling it.
  The transmission sign blinks when a signal is sent.

 

Display

 

This indicates the room temperature selected, current time, timer status, function 
and intensity of circulation selected.

 

START/STOP button

  Press this button to start operation. Press it again to stop operation.

 

SLEEP button

  Use this button to set the sleep timer.

 

TEMPERATURE buttons

  Use these buttons to raise or lower the temperature setting. (Keep pressed, 

and the value will change more quickly.)

 

TIME button

  Use this button to set and check the time and date.

 

RESET buttons

 

FUNCTION selector

  Use this button to select the operating mode. Every time you press it, 

the mode will change from 

 (AUTO) to   (HEAT) to 

 (DEHUMIDIFY) to 

 (COOL) and to 

 (FAN) cyclically.

 

FAN SPEED selector

 

This determines the fan speed. Every time you press this button, the intensity 
of circulation will change from     (AUTO) to     (HI) to     (MED) to     (LOW) 
(This button allows selecting the optimal or preferred fan speed for each 
operation mode).

 

AUTO SWING button

  Controls the angle of the horizontal air de

fl

 ector.

 

TIMER control

  Use this button to set the timer.

 

OFF-TIMER button

   Select the turn OFF time.

 

ON-TIMER button

   Select the turn ON time.

 

RESERVE button

   Time setting reservation.

 

CANCEL button

   Cancel time reservation.

Precautions for Use

  Do not put the remote controller in the following places.

 

  Under direct sunlight.

 

  In the vicinity of a heater.

  Handle the remote controller carefully. Do not drop it on the 

fl

 oor, 

and protect it from water.

  Once the outdoor unit stops, it will not restart for about 3 minutes 

(unless you turn the power switch off and on or unplug the power 
cord and plug it in again).

 

This is to protect the device and does not indicate a failure.

  If you press the FUNCTION selector button during operation, the 

device may stop for about 3 minutes for protection.

(EN1) RAK-60-70NHA1   6

(EN1) RAK-60-70NHA1   6

3/27/14   6:24 PM

3/27/14   6:24 PM

Содержание RAK-60NHA1

























Отзывы: