58
Vacuum Compartment
Once a month
Pull out the Vacuum Case.
For how to remove,
Pg.60
Be sure to remove foods contained in the Vacuum Case.
Wipe off following parts with a soft cloth
which is steeped in lukewarm water.
※
Do not use the detergents, etc.
Attach the Vacuum Case.
For how to attach,
Pg.60
1
2
3
Loosened vacuum compartment gasket or loose-fitting door of the
Vacuum Case may cause the vacuum state unable to keep well.
●
Wipe the ceiling of the compartment (platinum catalyst
and LED light) gently. Failing to do so may cause damage.
●
If detergents and others except lukewarm water are used to clean
the vacuum compartment gasket, the vacuum compartment
gasket may be damaged, deformed or change in color, which
may cause the vacuum state unable to keep well.
Request
Vacuum
Container
Vacuum Compartment
Gasket seat
Aluminum Tray
Vacuum
compartment
gasket
Ice Maker Cleaning
When using for the first time
When not used for more than one week
Wash the Ice Tray or water paths with water.
Be sure to check the followings before starting the operation.
Go to the next step after checking them.
Close all the doors.
Pre
pa
ra
tio
n
1
Hold down
button for 5 seconds
or more until the alarm sounds.
When the 3 indicator lamps “
急速製冰
(Quick Ice Making)” ,
“
製冰
(Ice Making)” and “
製冰停止
(Stop)” start to blink and
alarm starts to sound, stop holding the button.
“
製冰機清潔
(Ice Maker Cleaning)” starts (for about 4
minutes).
・
The indicator lamp will flash and the buzzer will sound for
about 4 minutes.
・
“
製冰機清潔
(Ice Maker Cleaning)” can’ t be interrupted.
・
If you open any of the refrigerator doors during Ice Maker
Cleaning, the cleaning may not work properly. Do not
open or close the door until
cleaning is completed.
・
Door alarm sounds even
if alarm is disabled.
Pg.55
Place a clean towel, etc. on the bottom in the
Ice Case so that the cutout of the Ice Case can
be blocked after the alarm and blinking of the
indicator lamp end.
Place a water-absorbing towel
on the bottom in the Ice Case to
prevent trapped water during the
ice maker cleaning from spilling
out of the cutout of the Ice Case.
Wipe off water inside the Ice Case completely,
and then set it to the Ice Compartment.
Remove the towel with which you
have wiped off water. There is no
problem with using water remaining
in the water supply container, if any.
After “
製冰機清潔
(Ice Maker Cleaning)” , it is set to “
製冰
(Ice Making)” mode, etc.
2
3
4
Cutout
Towel
Water supply container
・
Water is filled in it up to the limit
line.
・
It is set correctly beyond the
tank set position line.
Ice case
・
If there remains ice, remove it.
It blinks
Warning
●
Do not place your hand in the mechanical
section of the automatic ice maker.
(Rotation of the ice tray may cause injury.)
VARIOUS FUNCTIONS
(CONTINUED)
Remove the vacuum compartment gasket
from the Vacuum Case.
Grasp the tab of the vacuum
compartment gasket on the
observer’ s upper right and
remove it by hand carefully.
When the Vacuum Compartment Gasket is dirt
Wipe off excess moisture with a dry
cloth and dry it out naturally.
Attach the vacuum compartment gasket.
Align the tab to the notch accurately, and then combine
them together.
Wipe off dirt in the vacuum
compartment gasket
mounting groove.
Rinse dirty portion in water using a soft sponge, etc.
※
Do not use the detergents, etc.
1
2
3
5
4
Tab
Groove for attaching the vacuum compartment gasket.
Notch of the groove
Tab
Push it
