background image

GD-2500 DVD-ROM Manual 13

A commercially available “Laser Lens Cleaning Disc” may be used to clean up the
pick-up lens of the DVD-ROM drive. Use the Compact Disc Laser Lens Cleaner LLC-1.
(by AUDIO SOURCE in U.S.A., by AKUSTIK SISTEME VERTRIEBS GHBH in GERMANY
and by SAEC COMMERCE CO., LTD. in JAPAN.)

1) Turn on the DVD-ROM drive.
2) Using the small brush supplied with the cleaning disc case, straighten up    

the disc cleaning brushes on the back of the cleaning disc.

3) Place the cleaning disc in the disc tray with its arrow marked on the

disc at front.

4) Press the OPEN/CLOSE button or push the center of the disc tray   

lightly and close the disc tray.

5) After about 20 seconds, the pick-up lens is cleaned by the cleaning disc.
6) Press the OPEN/CLOSE button and remove the cleaning disc.
7) Set the cleaning disc in its case with the disc cleaning brushes in the pad   

hole.

8) Restart the SYSTEM.

1.  Turn off the DVD-ROM drive and wait at
least 15 seconds until the disc stops
rotating.  

2.  Insert  a straightened paper clip into
the Manual Emergency Eject Hole about 25
mm (1 inch).

3. Pull the disc tray.

NOTE:

If it is necessary to use the emergency eject procedure to open the drive, the

tray should be closed by turning on the power and pressing the OPEN/CLOSE button.
Transporting the drive before it has been properly closed may cause damage to the
mechanism.

Removal Procedure

Lens Cleaning

Содержание GD-2500
















Отзывы: