Hitachi DH24PF3 Скачать руководство пользователя страница 22

Страница: 22 / 44

--- 19 ---

8-3. "Three-Mode" Changeover Mechanism

The change lever of the Model DH 24PF3 permits quick and easy changeover among the "rotation and

hammering", "rotation only" and "hammering only" functions. Each function mode is explained below. When

operating the change lever, be sure to continue pressing the pushing button.

(1) Rotation and hammering (Fig. 6)

Adjust the change lever to "rotation and hammering" ( marks). Armature rotation is transmitted to the first

gear and second shaft, and then to the clutch via the spline of the second shaft. Claws on the end surface of

the clutch engage with matching claws of the reciprocating bearing ( A portion in the figure) to convert the

rotation into reciprocating motion. Three claws on the tip of the second shaft engage with matching three

claws of the pinion sleeve all the time, and the second shaft rotation is transmitted to the pinion sleeve. Then

claws on the large-dia. portion of pinion sleeve engage with the second pinion ( B portion in the figure), and

the rotation is transmitted to the second gear and the cylinder.

Armature

Cylinder

Spline of second shaft

Second gear

Change lever

Fig. 6

Clutch

A portion is meshed.
(Hammering transmitted.)

Second shaft

First gear

Reciprocating bearing

B portion is meshed.
(Rotation transmitted.)

Three claws of the second shaft

Pinion sleeve

Second pinion

Содержание DH24PF3













































Результаты поиска

Содержание DH24PF3

Отзывы:

Похожие инструкции для DH24PF3

Бренды по названию

Популярные бренды

Hitachi DH24PF3, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание DH24PF3

Отзывы:

Похожие инструкции для DH24PF3

Бренды по названию

Популярные бренды