manualshive.com logo in svg

Hitachi DH 24PD3, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Hitachi DH 24PD3 Скачать руководство пользователя страница 5

--- 2 ---

4. SELLING POINTS

Non-slip double-layer
molded handle

Class-top drilling speed
More comfortable and frisky drilling
Class-top dust collection efficiency
New and powerful design

Non-slip double-layer
molded gear cover

Internal pressure
adjustment mechanism

4-1. Selling Point Descriptions

4-1-1. Class-top drilling speed

The drilling speed of the Model DH 24PD3 is 1.5 times higher than B and 1.3 times higher than C and D thanks to

the efficient transmission of the hammering energy.

4-1-2. More comfortable and frisky drilling

The Model DH 24PD3 can drill holes more comfortably and friskily with a light pushing force because the quantity

of body jumping is 20% less than C.

4-1-3. Internal pressure adjustment mechanism

By minimizing variations in the internal pressure during operation, hammering operation is stabilized.  In addition,

idling and grease leakage can be prevented.

4-1-4. Class-top dust collection efficiency

The dust collection efficiency of the Model DH 24PD3 is equivalent to that of the Model DH 24PD2 and 6% higher

than B thanks to the efficient transmission of the hammering energy and the improved dust collection construction.

4-1-5. Non-slip double-layer molded gear cover

The double-layer molded gear cover consists of a plastic resin base covered with a soft resin to ensure ease of

operation and a non-slip grip during chipping (using a round bull point).

4-1-6. Non-slip double-layer molded handle

The double-layer molded handle consists of a plastic resin base covered with a soft resin to ensure a soft-touch

and non-slip grip.

Содержание DH 24PD3













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды