Hitachi CR 10DL, Инструкция по эксплуатации

Страница: 6 / 176

6
English
● Regarding the temperatures and charging time of the
battery.
The temperatures and charging time will become as
shown in Table 2 .
Table 2
Charger
Battery
UC10SL2
Charging voltage V 10.8
Weight kg 0.35
Type of battery Li-ion
Temperatures at which the
battery can be recharged
0 o C – 50 o C
Charging time for battery
capacity, approx. (At 20 o C)
1.3 Ah
1.5 Ah
3.0 Ah
min.
min.
min.
25 (3 cells)
30 (3 cells)
60 (6 cells)
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (o ff for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger’s
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
○ Since the built-in micro computer takes about 3 seconds to
con fi rm that the battery being charged with charger is taken
out, wait for a minimum of 3 seconds before reinserting it
to continue charging. If the battery is reinserted within 3
seconds, the battery may not be properly charged.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the
battery
1 165
Charging 2 165
Mounting the blade 3 165
Removing a broken blade 4 165
Maintenance and inspection of
saw blade mount
5 166
Base setting 6 166
Switch Operation 7 166
Select a saw blade of the
appropriate length
8 166
Securing the materials to be cut 9 167
Plunge cutting 10 167
How to use the LED light 11 167
Battery level warning lamp
(Indicates that the battery level is
low and requires recharging.)
12 167
Selecting accessories ― 168
SELECTION OF BLADES
To ensure maximum operating e ffi ciency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut.
The blade number is engraved in the vicinity of the mounting
portion of each blade. Select appropriate blades by referring
to Table 3-5 .
Table 3: HCS blades
Blade
No.
Uses
Thickness
(mm)
No. 2 For cutting steel pipe less than 30
mm in diameter
2.5 – 6
No. 3 For cutting steel pipe less than 30
mm in diameter
Below 3.5
No. 5 For cutting and roughing lumber Below 30
No. 96 For cutting stainless pipe less than
30 mm in diameter
Below 2.5
Table 4: Bl-METAL blades
Blade
No.
Uses
Thickness
(mm)
No. 101 For cutting steel and stainless
pipes less than 60 mm in outer
diameter
2.5 – 6
No. 103 For cutting steel and stainless
pipes less than 60 mm in outer
diameter
2.5 – 6
No. 107 For cutting steel and stainless
pipes less than 60 mm in outer
diameter
Below 3.5
No. 109 For cutting steel and stainless
pipes less than 60 mm in outer
diameter
2.5 – 6
0000Book̲CR10DL.indb 6 0000Book̲CR10DL.indb 6 2015/02/20 14:25:14 2015/02/20 14:25:14