Hitachi CG2026S, Руководство по обслуживанию

Страница: 18 / 42

17
HOTEL MODE
Hotel mode is a feature in the software in this receiver. However we do supply a special remote control which has access
to the menu’s denied.
This means that the T V can be tuned in, and set up with the original remote control, then the special remote is left with
the receiver.
EEPROM INITIALISATION
If the E²PROM IC500 is replaced it will come fully programmed and therefore it is not necessary to initialise the new device.
In some circumstances the E²PROM may become corrupted in use i.e. static discharge or lightning strike. If this happens,
it is advised that the E²PROM is replaced.
OFF AIR SIGNAL PATH
TUNER
A UV1315 voltage controlled tuner is used on th is chassis, operating from a 5volt supply, line (pin 6). A 0 to 33 volt
rail is used for tuning (pin 2), controlled by the microprocessor IC501. The AFT pin on the tuner is not used, instead the
Automatic Fine Tuning is achieved by modifying the tuning control line. This is done by software in IC501. The gain of the
tuner can be altered by the AGC control voltage fed in to pin 1.
The tuner produces a balanced output on pins 10,11. Neither side is connected to earth. This is fed via a surface wave
filter Z402 to the IF input of IC403 (pins 6 and 7).
IC403 incorporate the IF amplification, AFT , AGC, video and sound detectors as well as AV switching. The IC requires
both 5 and 8V tuned circuit for these functions, L401, L402, L403, and L406.
VIDEO PATH
The detected video signal is output from pins 13 of IC403, to sound traps Z403/404. The video is taken from the other side
via the appropriate filter to Pin 18 of IC403. (1.2 p to p) Video to the scart connectors is taken after R458 to Pin 19 of the
scart connector. The CVBS_TXT output Pin 29 output is fed to IC501 Pin 34 (for teletext). The video signal is sometimes
labelled CVBS on the circuit diagram. This stands for Composite Video Blanking & Sync.
The composite signal is input Pin 13 (Video input) of IC403. This IC carries out all of the luma/Chroma processing internally
and also provides the customer control functions of brightness, contrast, sharpness and saturation. IC403 is I²C bus
controlled and incorporates auto greyscale circuitry and internal luma/chroma delay lines. The resulting R.G.B drive is output
on pins 30,31 and 32. The R.G.B passes via connector PL405 to the CRT base PCB. Here the R.G.B signal is amplified by
IC901 to provide drive for the cathodes of the CRT. IC901 produces a feedback signal which is fed to IC403 (pin 33) for
blanking and auto grayscale correction.
SOUND PATH
The demodulated mono sound is taken from pin 55 of IC403 directly to the sound output stage IC401 Pin 7. The output
signal from IC401 is Volume controlled achieved within IC403 using the I²C bus line from IC501. To limit the volume at the
specified out put the A_out pin 55 is fed to IC 401 through a voltage divider R455 and R454. Muting of the output stage is
provided from Pin 46 of IC501 to pin3 of IC401/6 of IC301.
IN the stereo model the IF from PINS 10 & 11 of the tuner passes through Z401 and the output signal goes through pins
1&2 of IC403. The output QSS signal from IC 403 is taken from pin 11 and sent to audio processor IC700. The left channel
is output on PIN 29 and the right channel output is on PIN 28.Then to IC301 after passing through a voltage divider
R454/R455 for the right channel and R463/R464 for the left channel.
IC403 handles also the AM modulated signals in L/L’ systems at pins 1&2.
AV INPUT SIGNAL PATH
Video and Sound
IC403 has three CVBS inputs at pins 18,20 and 22.The composite video signal of AV1 is taken from pin 41 of the scart
connector to pin20 of IC403. The mono sound signal is taken from pins 2 and 6 of the scart sockets to the switching
transistors Q101. The transistor switch the audio depending on the source, and is then fed to pin 14 of lC403. The CVBS
coming from AV2 or AV3 is taken from pin 20 of scart connector, from the JK1 for BAV or JK4 for FAV. Then these signals
are switched by transistors Q141, Q142 depending on the source by the microprocessor’s pins 5,6,7. The resultant
signal is given to pin 22 of IC403.
Scart two supports also SVHS signals and then the chroma comes from pin 15 of connector PL101 directly to pin 23 of
IC403, whilst the luma uses the same path as the CVBS of AV2.
When AV input is selected pin 5,6,7 of the microprocessor IC50
1
is taken high, this switches the IC403 to external input
mode via I²C BUS. This connects the video inputs on pins 20 or 22 to IC403 and the audio input on pin 14 to the audio out
on pin 55 (via the internal volume control circuit) The signal paths are then as for off air.
The chassis can detect the video signals on scart1 and 2 using pin 8 switching voltages at pins 56 and 55 of IC501.