manualshive.com logo in svg

Hitachi C28W440N, Руководство по обслуживанию

Поделиться
Скачать
Hitachi C28W440N Скачать руководство пользователя страница 19

 

19

• 

  Cascadable with another TEA6415C (Internal address can be changed by pin 7 voltage) 

• 

  8 inputs (CVBS, RGB, Mac, CHROMA, … ) 

• 

  6 Outputs 

• 

 Possibility of MAC or chroma signal for each input by switching off the clamp with an external resistor 

bridge 

• 

  Bus controlled 

• 

  6.5dB gain between any input and output 

• 

  -55dB crosstalk at 5MHz 

• 

  Fully ESD protected 

 

PINNING  

PIN VALUE 

1.  Input 

:  Max 

: 2Vpp, Input Current 

: 1mA,  Max  : 3mA  

2. Data 

: Low level : -0.3V Max:1.5V, High level : 3.0V  Max : Vcc+0.5V 

 
3.  Input 

:  Max 

: 2Vpp, Input Current 

: 1mA,  Max  : 3mA  

4. Clock 

: Low level : -0.3V Max:1.5V, High level  : 3.0V Max : Vcc+0.5V  

 
5.  Input 

:  Max 

: 2Vpp, Input Current 

: 1mA,  Max  : 3mA  

6.  Input 

:  Max  

: 2Vpp, Input Current 

: 1mA,  Max  : 3mA  

7.  Prog 

 

8.  Input 

:  Max 

: 2Vpp, Input Current 

: 1mA,  Max  : 3mA  

9.  Vcc 

:  12V 

10. Input 

:  Max 

: 2Vpp, Input Current 

: 1mA,   Max  : 3mA  

11. Input 

:  Max 

: 2Vpp, Input Current 

: 1mA,   Max  : 3mA  

12. Ground 
13. Output 

:  5.5Vpp,  

Min : 4.5Vpp 

14. Output 

:  5.5Vpp,  

Min : 4.5Vpp 

15. Output 

:  5.5Vpp,  

Min : 4.5Vpp 

16. Output 

:  5.5Vpp,  

Min : 4.5Vpp 

 

17. Output 

:  5.5Vpp,  

Min : 4.5Vpp 

18. Output 

:  5.5Vpp, 

Min : 4.5Vpp 

19. Ground 
20. Input 

:  Max : 2Vpp, Input Current 

: 1mA,   Max  : 3mA  

 

16.4. 

TDA7265: 

The TDA7265 is a 25W+25W stereo sound amplifier with mute/stand-by facility. STPA control signal coming 
from microcontroller (when it is at high level) activates the mute function. IC is muted when mute port is at low 
level. Two stereo audio signals coming from audio module is injected to the inputs of the IC and a power of 
12Wrms (10%) is obtained. An external pop-noise circuitry pulls AF inputs of the IC in order to eliminate pop 
noise when TV is turned on or off via mains supply connection. It is possible to adjust the gain of the amplifiers by 
feedback external resistors. 
 

 

 

IN+1

IN+1
IN-(1)

IN-(1)

GND

GND
IN-(2)

IN-(2)

IN+(2)

IN+(2)
-V

S

-V

S

MUTE

MUTE
OUTPUT(2)

OUTPUT(2)

+V

S

+V

S

OUTPUT(1)

OUTPUT(1)

-V

S

-V

S

Содержание C28W440N
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды