Hitachi C 10FCE Скачать руководство пользователя страница 20

Страница: 20 / 62

--- 16 ---

Cutting method of crown molding without tilting the saw blade

6 mm wing bolt

Crown molding stopper (L)
(optional accessory)

Crown molding stopper (R)
(optional accessory)

6 mm wing
bolt

Crown molding
vise ass'y
(optional
accessory)

(1) Crown molding stopper (L) and (R) (optional

accessories) allow easier cuts of crown molding without

tilting the saw blade. Install them to both sides of the

base as shown in Fig. 22. After inserting, tighten the

6 mm knob bolts to secure the crown molding guides.

[ Optional accessories used ]

Crown molding vise ass'y

(include crown molding stopper (L))

Crown molding stopper (L)

Crown molding stopper (R)

(2) The crown molding vise ass'y (optional accessory) can

be mounted on either the left fence (fence (B)) or the

right fence (fence (A)). It can unite with the slope of the

crown molding and vise can be pressed down. Then

turn the upper knob, as necessary, to securely attach

the crown molding in position. To raise or lower the vise

assembly, first loosen the 6 mm knob bolt.

After adjusting the height, firmly tighten the 6 mm wing bolt; then turn the upper knob, as necessary, to

securely attach the crown molding in position. (See Fig. 23.)

WARNING: Always firmly clamp or vise to secure the crown molding to the fence; otherwise the crown

molding might be thrust from the table and cause bodily harm. Do not perform bevel cutting.

The main body or saw blade may contact the sub fence, resulting in an injury.

CAUTION: Always confirm that the motor head does not contact the crown molding vise ass'y when it is

lowered for cutting. If there is any danger that it may do so, loosen the 6 mm knob bolt and

move the crown molding vise ass'y to a position where it will not contact the saw blade.

Position crown molding with its WALL CONTACT EDGE against the guide fence and its CEILING CONTACT

EDGE against crown molding stoppers as shown in Fig. 23. Adjust the crown molding stoppers according to

the size of the crown molding. Tighten the 6 mm wing bolt to secure the crown molding stoppers.

Fig. 22

Fig. 23

Crown molding vise ass'y
(optional accessory)

Crown molding

6 mm wing bolt

Fence

6 mm knob bolt

Crown molding stopper (L)
Crown molding stopper (R)

(optional accessories)

Knob

6 mm wing
bolt

Содержание C 10FCE































































Результаты поиска

Содержание C 10FCE

Отзывы:

Похожие инструкции для C 10FCE

Бренды по названию

Популярные бренды

Hitachi C 10FCE, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание C 10FCE

Отзывы:

Похожие инструкции для C 10FCE

Бренды по названию

Популярные бренды