background image

FREEZE

FREEZE

35

PICTURE-IN-PICTURE (PIP)

FREEZE button (With PIP ON)

If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a
mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button
again.

FREEZE button (with PIP OFF)

Press the FREEZE button to freeze the picture, depending on the PIP mode selected (POP Main Freeze, POP Sub Freeze, SPLIT
and STROBE).
To change FREEZE modes, use the PIP MODE button to cycle through the four different modes.

POP MAIN FREEZE (with PIP OFF)

PIP FREEZE should be in POP MAIN mode. Press the FREEZE button to freeze one frame of the picture you are currently viewing
and the frozen frame will show in the Main Picture. Press this button again or PIP to return to normal viewing. This feature is useful
for freezing a picture frame with addresses.

POP SUB FREEZE (with PIP OFF)

PIP FREEZE should be in POP SUB mode. Press the PIP button and then press the FREEZE button to freeze the sub-picture.
Press the FREEZE button again and press the PIP button to return to normal viewing.

NOTES:

1. Each freeze frame is delayed about 0.1 (1/10) second.
2. When in ANT A/ANT B, the FREEZE mode cycles through POP-POP-SPLIT-STROBE.
3. When in ANT C, the FREEZE mode cycle will depend upon the signal format received.

NOTE:

When PIP is on, the FREEZE function will only operate when POP/PIP/SPLIT mode is chosen.

Hot Springs Clay Mask

C/O John Doe 

Run-Spa Retreat

P.O. Box 55512

Any Town, USA  98765

Check or

Money Order Only

1-800-555-1212

STROBE FREEZE(with PIP OFF)
PIP FREEZE should be in STROBE mode.

Press the FREEZE button to freeze three frames of the picture you are currently

viewing. Press this button again or PIP to return to normal viewing. This feature is useful for viewing a moving picture that has many
details, for example, a close play in a sporting event or a golf swing.

FREEZE

FREEZE

SPLIT FREEZE(with PIP OFF)

PIP FREEZE should be in SPLIT mode. Press the FREEZE button to freeze the picture you are currently viewing (only the right
sub-picture will freeze). Press the FREEZE button again to return to normal viewing.

Ant A 12

FREEZE

Main Picture

Sub Picture

Hot Springs Clay Mask

C/O John Doe 

Run-Spa Retreat

P.O. Box 55512

Any Town, USA  98765

Check or

Money Order Only

1-800-555-1212

FREEZE

FREEZE

FREEZE

Ant A   10

Hot Springs Clay Mask

C/O John Doe 

Run-Spa Retreat

P.O. Box 55512

Any Town, USA 98765

Check or

Money Order Only

1-800-555-1212

Hot Springs Clay Mask

C/O John Doe 

Run-Spa Retreat

P.O. Box 55512

Any Town, USA  98765

Check or

Money Order Only

1-800-555-1212

THE

REMO

TE

CONTR

OL

Содержание 57T600

















































































Отзывы: