manualshive.com logo in svg

HiP T Series, Инструкция - Каталог запасных частей, Страница: 16 / 36

Поделиться
Скачать
HiP T Series Скачать руководство пользователя страница 16

Repair - Pump Lower 

16

3A6823A

7.

Low-pressure pumps only.

 Install the large 

o-ring (113) into the inlet port of the fluid 
cylinder (101), then install the inlet check 
housing (117). 

8.

Medium-pressure pumps only.

 Install the spacer 

(121) into the inlet port of the fluid cylinder (101), 
then install the inlet check housing (117).

9.

Low- and medium-pressure pumps only.

 Install 

the small o-ring (115) onto the check poppet (114), 
then install the poppet (114) and compression 
spring (116) into the outlet check housing (118), as 
shown.

10.

Low-pressure pumps only. 

Install the large 

o-ring (113) into the outlet port of the fluid 
cylinder (101), then install the outlet check housing 
(118). 

11.

Medium-pressure pumps only.

 Install the spacers 

(119 and 121) into the outlet port of the fluid cylinder 
(101), then install the outlet check housing (118).

12. Stack and install the seal stack, as shown. Use 

grease during installation.

13. Install the packing nut (109) with a medium strength 

thread locking compound, and torque to 5-10 ft-lbs 
(7-14 n•m). The packing nut (109) should be flush 
with the surface of the fluid cylinder (101).

Reconnect the Pump Lower

1.

Align the pump lower (3) so that the inlet port is to 
the left when facing the front of the pump (1).

2.

Install the screws (5), lock washers (4), and spacers 
(2), as shown in F

IG

. 4, and align with the holes in 

the bottom of the pump (1), as shown in F

IG

. 5.

3.

Torque the screws (5) to 50-60 ft-lbs (68-81 N•m).

F

IG

. 4 

F

IG

. 5 

1

3

5

4

2

111

5

3

110

Содержание T Series





































Отзывы:

Нет отзывов