background image

SS7012 Remote Interface Overview

2

Figure 1 shows a block diagram of the SS7012 remote interface.

Operating
principle

Communication between a personal computer and the SS7012 is virtual RS-232
serial communication. While the USB interface is installed as the transmission
route, actual communication uses RS-232.

It is necessary to issue RS-232 commands via the virtual COM port.
When RS-232 commands are issued to the virtual COM port, commands are
sent to the SS7012 in the following order. (For the receipt of data, the order is
reversed.)

SS7012 Remote Interface Overview

USB signal

Virtual COM
(Virtual RS-232C) port

USB 

⇔ 

RS-232 conversion

application

USB A connector

Central processing unit

(CPU)

USB 

 RS-232

conversion device

USB B connector

USB signal

USB device driver

Communication terminal 
software or application software

RS-232
compatibility signal

USB cable

Baud rate

: 9600bps (fixed)

Data bit

: 8bit (fixed)

Parity

: none (fixed)

Stop bit

: 1 (fixed)

Flow control : none (fixed)

SS7012

Personal Computer (PC)

Figure 1: Overview block diagram of the SS7012 remote interface

(PC internal)

Virtual COM port
(Communication signal via RS-232)

(PC internal)

USB 

 RS-232 data conversion

USB

(SS7012 internal)

USB 

 RS-232 conversion device

(SS7012 internal)

CPU
(Communication signal via RS-232)

Sending a command

Receiving data

Содержание SS7012





















Отзывы: