Hioki MR8827 Скачать руководство пользователя страница 52

Страница: 52 / 436

Adjust the Zero Position (Zero-Adjust)

2.7 Adjust the Zero Position (Zero-Adjust)

This procedure compensates for module differences and sets the reference potential of the instrument to

0 V.

The compensation procedure is performed for all channels and ranges.

Before Performing Zero-Adjust

•

Before performing this procedure, allow the equipment to warm up for about 30 minutes after the power

is turned on so the internal temperature of the modules can stabilize.

•

Note that zero-adjust cannot be performed during measurement.

•

Key operations are not accepted during zero-adjust.

•

The time required for zero-adjust varies depending on the type and number of modules installed in the

instrument. (The procedure may take several seconds.)

Procedure

Press the

CHAN

key to open the Channel screen, and then select the

[Unit List]

sheet.

Move the cursor to

[Zero-Adjust]

Select

[Exec Zero-Adjust]

The zero-adjust procedure is carried out.

Zero-adjustment has no effect on the 8969 and U8969 Strain Unit.

(Perform zero-adjust using auto-balance. (p. 168))

Perform zero-adjust in the following cases.

•

When a module was changed.

•

When power was turned off and on again.

•

When settings were initialized (system reset).

•

When DC/RMS is switched at the 8971 Current Unit and the 8972 DC/RMS Unit

•

When the ambient temperature has changed significantly.

Zero-position drift* may occur.

* Drift:

This refers to spurious output caused by a shift in the operating point of an operational amplifier. Drift can

occur due to changes in temperature and due to component aging over a period of use.

Measurement Preparation

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Hioki MR8827, Инструкция по эксплуатации, Страница: 52 / 436

Результаты поиска

Содержание MR8827

Отзывы: