Hioki MR8827 Скачать руководство пользователя страница 173

Страница: 173 / 436

168

Detailed Settings for Modules

8.10.4 Setting Model 8969 and U8969 Strain Unit

The Model 8969 or U8969 Strain Unit can perform auto-balance.

Executing the auto-balance adjusts the reference output level of the transducer to the specified zero

position.

This function can be used for Model 8969 or U8969 Strain Unit only.

The instrument describes Model U8969 as “8969.”

Before Executing Auto-balance

• Turn power on and wait 30 minutes to allow the internal temperature of the module

to stabilize.

• After connecting the strain gauge transducer to the module, execute the auto-

balance without any input including distortion.

• Auto-balance cannot execute during measurement.

• Key operations are not accepted while auto-balance is executing.

To Execute Auto-balance

Refer to “To Open [Each Ch] and Make a Channel Selection” (p. 164).

Setting Item:

[Range]

Auto Bal All Chs

Auto-balance will be executed for all channels where a Model 8969 or

U8969 Strain Unit is installed.

Auto Bal Ch 1

Auto-balance will be executed for the currently selected channel.

Auto-balance can also be executed from the Channel settings window (Analog sheet)

(if the range of a channel with an installed Model 8969 Strain Unit is selected).

To Open the Channel settings window ([Analog] sheet)

Refer to “3.4.2 Choose Analog Channel Settings” (p. 63).

In the following cases, auto-balance should be executed again.

• After changing the vertical axis (strain axis) range

• After a module has been removed or inserted

• After the strain gauge transducer has been replaced

• After power has been turned off and on

• After performing a system reset

•

When ambient temperature has changed significantly (the zero position may drift)

If “Warning: Auto balance failed.” appears

The channel on which auto-balance failed is displayed.

Verify the following, and execute again:

• Is the strain gauge transducer not subject to any load?

(Make sure that it is not subject to vibration, etc.)

• Is the strain gauge transducer connected correctly?

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Hioki MR8827, Инструкция по эксплуатации, Страница: 173 / 436

Результаты поиска

Содержание MR8827

Отзывы: