Hioki MR8827 Скачать руководство пользователя страница 318

Страница: 318 / 436

313

LAN Connection and Settings (Before Using FTP/Internet Browser/Command Communications)

16.1.2

Connect the Instrument to a PC With a LAN Cable

WARNING

When connecting the instrument to your LAN using a LAN cable of more than

30 m or with a cable laid outdoors, take appropriate countermeasures that

include installing a surge protector for LANs. Such signal wiring is susceptible to

induced lighting, which can cause damage to the instrument.

Connect the instrument to a PC with a LAN cable as follows.

Plug the LAN cable (100BASE-TX compliant) into the 100BASE-TX connector on the back
side of the instrument.

LINK LED

RX/TX LED

Lights while the instrument is capable of

communications with a destination device.

Flashes while data is being sent

or received.

Back side

Connect the above LAN cable to the PC.

There are two ways to do this.

1. Connect the Instrument to a Network

(Connecting the Instrument to a Hub)

You can monitor and control the instrument from a PC by connecting the instrument to a hub with

a LAN cable (100BASE-TX cable).

Connection cable: Use one of the following.

• 100BASE-TX straight-through cable (maximum length 100 m, commercially available)

(10BASE-T cable may also be used for 10BASE communications)

•

9642 LAN Cable (optional)

Connect to hub

100BASE-TX connector

Connect the cable to the 100BASE-TX connector on the instrument

and hub.

Connect to a PC

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды