Hioki MR8827 Скачать руководство пользователя страница 174

Страница: 174 / 436

169

Detailed Settings for Modules

8.10.5 Setting Model 8970 Freq Unit

When the standard logic display (LA, LB, LC, LD, LE, LF, LG, and LH) is on, 8970 Freq Units installed

as unit 1, 2, 9, or 10 cannot be used.

Refer to “To Open [Each Ch] and Make a Channel Selection” (p. 164).

Mode

Changes the measurement mode.

Frequency

Measure the frequency of the measurement waveform (Hz hertz)

(Default setting)

RPM

Measure the number of rotations of the measurement target

(r/min: rotations/minutes)

Power

Frequency

Measure the power frequency variation (Hz hertz)

Count

Add up the number of input pulses

Duty

Measure the duty rate of the measurement waveform (% percent)

Pulse width Measure the pulse width (s second)

Pulses with rises during dead time (calculation) (25 kHz or higher) cannot be measured.

Ignored

Calculation (40 μs)

Waveform

loaded

Waveform

loaded

VRange (Input

voltage)

Set the maximum level for the input signal.

±10 V

(Default setting)

, ±20 V, ±50 V, ±100 V, ±200 V, ±400 V

Select the value using the

keys.

Threshold value

• When the measurement waveform exceeds the threshold value, the measurement value is

acquired based on the time interval and the number of times the threshold was exceeded.

• The threshold value upper and lower limits and increases and decreases in width

depend on the input voltage ([VRange]) setting.

• While setting the threshold, the voltage level is displayed on the level monitor.

• Select the value using the

keys.

To prevent measurement errors due to noise, the threshold has a hysteresis of approximately 3%

versus the input voltage.

(When

[VRange]

[ ±10V]

, it is around ±0.3 V.)

Set a threshold in excess of the hysteresis width versus the voltage peak.

Utility Functions

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды