Hioki IM7580 Скачать руководство пользователя страница 29

Страница: 29 / 340

Connecting a Measurement Cable/Fixture

2.4 Connecting a Measurement Cable/Fixture

Please read “Before turning ON the power” (p. 7), “Handling of cords and fixtures” (p. 8)

before connecting the measurement cable/fixture.

Connect the measurement cables, or optional Hioki test fixture to the measurement terminals.

See “Options (Sold separately)” (p. 2) for options.

See the instructions provided with the fixture for operating details.

Note the following when extending the distance between test sample and measuring

terminals.

•

Use 50

coaxial cable for the measurement cable.

•

Make the length of the cable as short as possible.

•

Perform OPEN/SHORT/LOAD calibration using the connecting terminal of the test sample.

Use the specified probes and fixtures. When you make your own probe, it may not satisfy the

specifications of this instrument.

Refer to “Options (Sold separately)” (p. 2)

IM9906 Adapter (3.5 mm/7 mm)

(recommended torque, 0.9 N.m)

Test head

There are 3 screws, of

which only 2 are used in

this product.

IM9200 Test Fixture

Stand

This screw is not used in

this product.

Fix the test head to the IM9200

Test Fixture Stand.

Install the IM9906 Adapter

(3.5 mm/7 mm) to the

measurement terminal of the

test head (recommended torque,

0.9 N.m).

Perform calibration with the

calibration kit.

Place the IM9201 SMD test fixture

on the IM9200 Test Fixture Stand,

and connect a 7-mm connector.

(recommended torque, 1.35 N.m)

Measurement Preparations

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды