Hioki IM7580 Скачать руководство пользователя страница 27

Страница: 27 / 340

Pre-Operation Inspection

2.2 Pre-Operation Inspection

Please read “Operating Precautions” (p. 6) before use.

Before using the instrument for the first time, verify that it operates normally to ensure that no

damage occurred during storage or shipping.

If you find any damage, contact your authorized Hioki distributor or reseller.

Inspection of accessories and options

Inspection item

Solution

Is the power cord insulation torn, or is any metal

exposed?

Do not use the instrument if damage is found, as it can

result in electric shocks or short-circuit accidents.

Contact your authorized Hioki distributor or reseller.

Is the insulation on the measurement cable torn, or is

any metal exposed?

If there is any damage, measured values may be unstable

and measurement errors may occur.

Replace the cable with an undamaged one.

Instrument inspection

Inspection item

Solution

Is the instrument damaged?

If the instrument is damaged, request repairs.

Does the Opening screen appear (Model no., version

no.) when the power is turned on?

Screen when the power is turned on

If the Opening screen does not appear, the power cord may

be damaged, or the instrument may be damaged internally.

Request repairs.

Is there an error displayed on the Opening screen?

Error display screen

If there is an error displayed, the instrument may be

damaged internally. Request repairs.

Reference: “Troubleshooting” (p. 297), “Error Display”

(p. 303)

Example: An interface board which cannot be used is

installed (LAN board).

Measurement Preparations

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды