Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 137

background image

6

THE PRESENT MANUAL HAS TO BE CONTEMPLATE WITH INDICATIVE
PURPOSE, IT DOESN'T REPLACE ANYHOW MACHINE USE AND
MAINTENANCE MANUAL.
UNANNOUNCED VARIATIONS AND CORRECTIONS COULD BE APPLIED
ON MACHINES AND ON THE PRESENT DOCUMENT.
THEREFORE ALWAYS REFER TO USE AND MAINTENANCE MANUAL FOR
ORDINARY AND EXTRAORDINARY USAGE, FOR MAINTENANCE, FOR
PROBLEM SOLVING AND GENERALLY FOR ANYTHING REGARDING THE
MACHINE.

1.

INTRODUCTION

This booklet describes the technical and safety features, the electrical system

and the hydraulic system of the Hinowa LightLift 15.70 3S Performance.
It does not include how to operate the machine, for this purpose refer to the

Operation and Maintenance Manual.
The first two digits of numerical part of the LightLift name identify the machine

maximum  working  height  in  meters,  while  the  last  two  digits  indicate  the
maximum outreach in decimetres.
The  aerial  platform  is  equipped  with  an  hydraulic  system  and  an  electrical

system that interact to ensure safe operating in any situation.
The present manual describes those two systems and how they interact.

1.1

PARTS DENOMINATION

The base sides of the machine are established looking from inside the basket,
which is positioned in the rear side as indicated in the draft below.

The aerial part booms are numerated looking from the base, i.e. from the turret

slew ring, to the basket as indicated in the draft below.
All the machine movements are controlled by the machine remote control

supplied with the machine. Usually, the remote control is positioned in the

LEFT

SIDE

REAR

SIDE

FRONT

SIDE

RIGHT

SIDE

OUTRIGGER

N.1

OUTRIGGER

N.4

OUTRIGGER

N.3

OUTRIGGER

N.2

«
...
4
5
6
7
8
...
»

Содержание LightLift 15.70 3S










































































































































Отзывы:

Нет отзывов

Похожие инструкции для LightLift 15.70 3S

Бренд: QUALITY LIFTS Страницы: 21

Бренд: WAREMA Страницы: 112

WAGO-I/O-SYSTEM 750 XTR Series

Бренд: WAGO Страницы: 272

Бренд: WAGO Страницы: 450

Бренд: R. Beck Maschinenbau Страницы: 34

RAZORWELD ARC 630

Бренд: Xcel-Arc Страницы: 36

Бренд: IBCcontrol Страницы: 16

Бренд: WattMaster Страницы: 104

Бренд: Mandik Страницы: 34

Бренд: Mithraeum Страницы: 33

Бренд: Fronius Страницы: 100

Бренд: Tarfire Страницы: 31

Бренд: Mantracourt Страницы: 24

Бренд: Dino lift Страницы: 121

Бренд: Miller Electric Страницы: 48

Бренд: Vasco Страницы: 32

Бренд: salmson Страницы: 40

SENTEX Infinity B Series

Бренд: Chamberlain Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды